Posts made by dejvid17

undefined

@rushmere3d
At this moment I have problem with printing. Filament move after extruder and after few sec is a one big ball

undefined

@rushmere3d
I know.. I should start from learning gcode commands but I thought it will be much easier..

undefined

@rushmere3d
Do you know where I can find right config superslicer?
I've been tring few option but results the same

Warning: Macro file pause.g not found

Error: Bad command: START_PRINT EXTRUDER_TEMP=225 BED_TEMP=75
Error: Bad command: SET_GCODE_OFFSET Z=0
Error: Bad command: SET_PRESSURE_ADVANCE ADVANCE=0.05

undefined

@rushmere3d

undefined

@rushmere3d

undefined

@dc42
I know I'm annoing but

Error: Heater 1 fault: heater monitor 0 was triggered
Resume state saved
Warning: Macro file pause.g not found
Printing paused at X250.0 Y250.0 Z10.9

M32 "0:/gcodes/1111111.gcode"
File 0:/gcodes/1111111.gcode selected for printing
Warning: M73: Command is not supported
Error: Bad command: START_PRINT EXTRUDER_TEMP=248 BED_TEMP=108
Error: Bad command: SET_GCODE_OFFSET Z=0.0
Error: Bad command: SET_PRESSURE_ADVANCE ADVANCE=0.03

config-override.g

; config-override.g file generated in response to M500 at 2022-08-10 16:57
; This is a system-generated file - do not edit
; Heater model parameters
M307 H0 R0.582 C398.938:398.938 D3.39 S1.00 V24.3 B0
M307 H1 R2.788 C216.240:216.240 D8.68 S1.00 V24.2 B0
; Workplace coordinates
G10 L2 P1 X0.00 Y0.00 Z0.00
G10 L2 P2 X0.00 Y0.00 Z0.00
G10 L2 P3 X0.00 Y0.00 Z0.00
G10 L2 P4 X0.00 Y0.00 Z0.00
G10 L2 P5 X0.00 Y0.00 Z0.00
G10 L2 P6 X0.00 Y0.00 Z0.00
G10 L2 P7 X0.00 Y0.00 Z0.00
G10 L2 P8 X0.00 Y0.00 Z0.00
G10 L2 P9 X0.00 Y0.00 Z0.00
M486 S-1

I add command M501 on the end of config.g

undefined

@dc42

I don't know what to do now...
I can't manual set temperature of the hotend only command M303 H1 S works and when I tried to print something super slicer set hotend 248 degrees but after minute againg error about rising temp too slow

; Endstops
M574 X1 S1 P"io0.in" ; configure active high endstops
M574 Y2 S1 P"io1.in" ; configure active high endstops

M671 X-4.5:250:504.5 Y-4.52:505:-4.52 S5 ; define positions of Z leadscrews or bed levelling screws
M557 X20:480 Y20:480 P5 ; define 5x5 mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B3950 A"Bed" ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out5 and map it to sensor 0
M307 H1 R2.794 C222.6 D8.63 S1.00 V24.2 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S110 ; set temperature limit for heater 0 to 110C

;; Run Bed PID Tune!! Below is an example for a 300x300 bed
M307 H0 A303.1 C356.7 D1.4 S1.00 V24.0 B0

; Fans
M950 F0 C"out4" Q500 ; create fan 0 on pin out4 and set its frequency
M106 P0 C"Layer Fan" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned off
M950 F1 C"out3" Q500 ; create fan 1 on pin out3 and set its frequency
M106 P1 C"Hotend Fan" S0 H1 T45 ; set fan 1 name and value. Thermostatic control turned on for Hotend

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

M950 H1 C"out1" T1 ; create nozzle heater output on out2 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S250 ; set the maximum temperature in C for heater

; EVA 2 / BMG / E3D V6

M92 E830 ; set extruder steps per mm, 0.9 angle/step (LDO Pancake)
M906 E800 ; set extruder motor current (mA) and idle factor in per cent

M308 S1 P"temp1" Y"thermistor" T100000 B4725 C7.060000e-8 A"Hotend"
;; Run Heater PID Tune!!
M307 H1 A751.5 C196.6 D4.7 S1.00 V23.9 B0

; Z-Probe
;; Inductive Probe
M558 P5 C"!io3.in" H5 F400 T5000 ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X-30 Y-15 Z0.20 ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed
; BLTouch
M950 S0 C"io2.out" ; Create a servo pin on io7
M558 P9 C"io2.in" H5 F240 T10800 A5 ; set Z probe type to unmodulated and the dive height + speeds
G31 P25 X-28.00 Y-13.00 Z0.90 ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed

; Select default tool
T0

; Pressure Advance
M572 D0 S0.10

undefined

@rushmere3d Yes both
and still the same problem Error: Heater 0 fault: temperature rising much more slowly than the expected 0.6°C/sec

undefined

@Rushmere3D
Super slicer fixed up in setting printer was Klipper.
but I don;'t know what do with that

Error: Heater 1 fault: heater monitor 0 was triggered
Error: Heater 0 fault: temperature rising much more slowly than the expected 1.7°C/sec

Error: Can't activate heater 0 while in fault state
Resume state saved
Warning: Macro file pause.g not found

config.g

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B3950 A"Bed" ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out5 and map it to sensor 0
M307 H0 A303.1 C356.7 D1.4 S1.00 V24.0 B0 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S110 ; set temperature limit for heater 0 to 110C

;; Run Bed PID Tune!! Below is an example for a 300x300 bed
;; M307 H0 A303.1 C356.7 D1.4 S1.00 V24.0 B0

; Fans
M950 F0 C"out4" Q500 ; create fan 0 on pin out4 and set its frequency
M106 P0 C"Layer Fan" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned off
M950 F1 C"out3" Q500 ; create fan 1 on pin out3 and set its frequency
M106 P1 C"Hotend Fan" S0 H1 T45 ; set fan 1 name and value. Thermostatic control turned on for Hotend

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

M950 H1 C"out1" T1 ; create nozzle heater output on out2 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S250 ; set the maximum temperature in C for heater

; EVA 2 / BMG / E3D V6

M92 E830 ; set extruder steps per mm, 0.9 angle/step (LDO Pancake)
M906 E800 ; set extruder motor current (mA) and idle factor in per cent

M308 S1 P"temp1" Y"thermistor" T100000 B4725 C7.060000e-8 A"Hotend"
;; Run Heater PID Tune!!
;; M307 H1 A751.5 C196.6 D4.7 S1.00 V23.9 B0

undefined

@rushmere3d
I send from super slicer project to printer and after a few sec first error heater 1 no pause.g file

no any of those files

undefined

@phaedrux

Guy's any ideas what this time is wrong????

undefined

@phaedrux thank you
Z should be 99999 and everything works fine..

undefined

@rushmere3d yes, but next time I correct manual level of the bed and again the same error

M671
Z leadscrew coordinates (-4.5,-4.5) (250.0,505.0) (504.5,-4.5), factor 1.00, maximum correction 5.00mm, manual adjusting screw pitch 0.50mm

when I change Z from -500 to 500 error almost the same G32
Error: Some computed corrections exceed configured limit of 5.00mm: 500.000 500.000 500.000

bed.g
; this script compensates for what the Z offset is
; so if G31 P500 X-30 Y-15 Z1.7 then first probe will be at
; X30 Y20 (when G30 P0 X0 Y5)

M561 ; clear any bed transform

G30 P0 X5 Y5 Z500 ; probe near a leadscrew
G30 P1 X150 Y285 Z500 ; probe near a leadscrew
G30 P2 X270 Y5 Z500 S3 ; probe near a leadscrew and calibrate 3 motors

undefined

@rushmere3d thank you !! I change 7 for 2 and home Z done..

but now I tried to bed leveling and another error

G32
Error: Some computed corrections exceed configured limit of 5.00mm: -500.000 -500.000 -500.000

undefined

@Phaedrux
I checked BLTouch wirring twice.
Yes, I delete two command inductive probe

undefined

I have one probe BLtouch.
When M558 is on in Z-probe / off in BLTouch bed goes up and can't stop
in other way off in Z-Probe / on in BLTouch still the same Error

I download a .zip config packeg from ratrig link
Please tell me what I should do with those strange commands

M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: Invalid Z probe index
Error: Unknown pin name 'io7.out'
Error: Unknown pin name 'io7.in'
Error: Invalid Z probe index

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.2.2 running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: GMDS7-G096U-D65J0-40KM0-M403Z-HS1D4
Used output buffers: 3 of 40 (12 max)
=== RTOS ===
Static ram: 98732
Dynamic ram: 107768 of which 228 recycled
Never used RAM 38488, free system stack 128 words
Tasks: NETWORK(ready,156) HEAT(blocked,315) CanReceiv(blocked,947) CanSender(blocked,358) CanClock(blocked,363) TMC(blocked,106) MAIN(running,418) IDLE(ready,20) AIN(blocked,269)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:20:31 ago, cause: power up
Last software reset at 2022-07-31 15:16, reason: User, GCodes spinning, available RAM 38488, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Aux1 errors 0,0,0
Supply voltage: min 0.0, current 24.3, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 40000, standstill, SG min/max 0/12, read errors 0, write errors 0, ifcnt 13, reads 49566, writes 13, timeouts 1, DMA errors 0, failedOp 0x6a
Driver 1: position 0, standstill, SG min/max 0/10, read errors 0, write errors 0, ifcnt 13, reads 49567, writes 13, timeouts 0, DMA errors 0
Driver 2: position 4000, standstill, SG min/max 0/12, read errors 0, write errors 0, ifcnt 13, reads 49567, writes 13, timeouts 0, DMA errors 0
Driver 3: position 0, standstill, SG min/max 0/20, read errors 0, write errors 0, ifcnt 12, reads 49568, writes 12, timeouts 0, DMA errors 0
Driver 4: position 0, standstill, SG min/max 0/2, read errors 0, write errors 0, ifcnt 13, reads 49567, writes 13, timeouts 0, DMA errors 0
Driver 5: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 10, reads 49570, writes 10, timeouts 0, DMA errors 0
Driver 6: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 9, reads 49571, writes 9, timeouts 0, DMA errors 0
Date/time: 2022-08-01 08:51:00
Cache data hit count 2515220930
Slowest loop: 14.00ms; fastest: 0.12ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 3.9ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 1173485ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 9, completed moves 9, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 24.80ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.25
WiFi MAC address f0:08:d1:03:7f:8e
WiFi Vcc 3.36, reset reason Power up
WiFi flash size 2097152, free heap 26184
WiFi IP address 192.168.2.223
WiFi signal strength -44dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0
=== CAN ===
Messages queued 11082, send timeouts 11079, received 0, lost 0, longest wait 0ms for reply type 0, free buffers 16

undefined

Hi everyone
I need some help with first config my rat rig vcore 500. Error like you see on the screen
I tried many option from few days but allways the same result. This is my first printer

config.g

; General preferences
G90                                     ; send absolute coordinates...
M83                                     ; ...but relative extruder moves
M550 P"V-Core 3"                        ; set printer name
M669 K1                                 ; CoreXY
G21                                     ; Set Units to Millimeters

; Network
M552 S1                                 ; enable network
M586 P0 S1                              ; enable HTTP
M586 P1 S0                              ; disable FTP
M586 P2 S0                              ; disable Telnet

; Drives
M569 P0.0 S0 D3                         ; physical drive 0.0 goes forwards
M569 P0.1 S0 D3                         ; physical drive 0.1 goes forwards
M569 P0.2 S0 D3                         ; physical drive 0.2 goes forwards
M569 P0.3 S1 D3                         ; physical drive 0.3 goes forwards
M569 P0.4 S1 D3                         ; physical drive 0.4 goes forwards
M569 P0.5 S1 D3                         ; physical drive 0.5 goes forwards
M584 X0.4 Y0.3 Z0.0:0.1:0.2 E0.5        ; set drive mapping
M350 X16 Y16 Z16 E16 I1                 ; configure microstepping with interpolation

M92 X80.00 Y80.00 Z800.00               ; set steps per mm
M906 X1000 Y1000 Z800 I30               ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                 ; Set idle timeout

M566 X400.00 Y400.00 Z6.00 E120.00 P1          ; set maximum instantaneous speed changes (mm/min)
M203 X10800.00 Y10800.00 Z1000.00 E3600.00     ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z100.00 E3600.00        ; set accelerations (mm/s^2)

; Axis Limits
M208 X0 Y0 Z0 S1                               ; set axis minima
M208 X510 Y500 Z500 S0                         ; set axis maxima

; Endstops
M574 X1 S1 P"io0.in"                           ; configure active high endstops
M574 Y2 S1 P"io1.in"                           ; configure active high endstops

M671 X-4.5:250:504.5 Y-4.52:505:-4.52 S5       ; define positions of Z leadscrews or bed levelling screws
M557 X20:480 Y20:480 P5                        ; define 5x5 mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B3950 A"Bed"    ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                                     ; create bed heater output on out5 and map it to sensor 0
M307 H0 B0 S1.00                                       ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                                ; map heated bed to heater 0
M143 H0 S110                                           ; set temperature limit for heater 0 to 110C

;; Run Bed PID Tune!! Below is an example for a 300x300 bed
;; M307 H0 A303.1 C356.7 D1.4 S1.00 V24.0 B0

; Fans
M950 F0 C"out4" Q500                   ; create fan 0 on pin out4 and set its frequency
M106 P0 C"Layer Fan" S0 H-1            ; set fan 0 name and value. Thermostatic control is turned off
M950 F1 C"out3" Q500                   ; create fan 1 on pin out3 and set its frequency
M106 P1 C"Hotend Fan" S0 H1 T45        ; set fan 1 name and value. Thermostatic control turned on for Hotend

; Tools
M563 P0 D0 H1 F0           ; define tool 0
G10 P0 X0 Y0 Z0            ; set tool 0 axis offsets
G10 P0 R0 S0               ; set initial tool 0 active and standby temperatures to 0C

M950 H1 C"out1" T1         ; create nozzle heater output on out2 and map it to sensor 1
M307 H1 B0 S1.00           ; disable bang-bang mode for heater and set PWM limit
M143 H1 S250               ; set the maximum temperature in C for heater

; EVA 2 / BMG / E3D V6

M92 E830          ; set extruder steps per mm, 0.9 angle/step (LDO Pancake)
M906 E800         ; set extruder motor current (mA) and idle factor in per cent

M308 S1 P"temp1" Y"thermistor" T100000 B4725 C7.060000e-8 A"Hotend"  
;; Run Heater PID Tune!! 
;; M307 H1 A751.5 C196.6 D4.7 S1.00 V23.9 B0

; Z-Probe
;; Inductive Probe
 M558 P5 C"!io3.in" H5 F400 T5000       ; set Z probe type to unmodulated and the dive height + speeds
 G31 P500 X-30 Y-15 Z0.20               ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed
;; BLTouch
 M950 S0 C"io7.out"                     ; Create a servo pin on io7
 M558 P9 C"io7.in" H5 F240 T10800 A5    ; set Z probe type to unmodulated and the dive height + speeds
 G31 P25 X-28.00 Y-13.00 Z0.90          ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed

; Select default tool
T0

; Pressure Advance
 M572 D0 S0.10

homeall.g

M201 X500.00 Y500.00    ; Reduce acceleration for homing moves

; BLTouch
M280 P0 S160           ; Precautionary alarm release
M280 P0 S90            ; Ensure the pin is raised

G91                     ; Relative positioning
G1 H2 Z5 F6000          ; Lift Z relative to current position
G1 H1 X-625 Y605 F3600  ; Move quickly to X and Y axis endstops and stop there (first pass)
G1 H1 X-625 F1800       ; Move quickly to X and Y axis endstops and stop there (first pass)
G1 H1 Y605 F1800        ; Move quickly to X and Y axis endstops and stop there (first pass)

G1 H2 X1 Y-1 F600       ; Go back a few mm

G1 H1 X-625 Y605 F360   ; Move slowly to X and Y axis endstops once more (second pass)
G1 H1 X-625 F360        ; Move slowly to X and Y axis endstops once more (second pass)
G1 H1 Y605 F360         ; Move slowly to X and Y axis endstops once more (second pass)

M201 X3000 Y3000        ; Return to full acceleration

G90                     ; Absolute positioning
;G1 X150 Y150 F10000     ; Go to the center of the bed (300x300)
;G1 X200 Y200 F10000    ; Go to the center of the bed (400x400)
G1 X250 Y250 F10000    ; Go to the center of the bed (500x500)
G30                     ; Home Z by probing the bed

G91                     ; Relative positioning
G1 Z5 F100              ; Lift Z relative to current position
G90                     ; Absolute positioning

homez.g

; BLTouch
M280 P0 S160           ; Precautionary alarm release
M280 P0 S90            ; Ensure the pin is raised

G91                     ; Relative positioning
G1 H2 Z5 F6000          ; Lift Z relative to current position

G90                     ; Absolute positioning
;G1 X150 Y150 F10000     ; Go to the center of the bed (300x300)
;G1 X200 Y200 F10000    ; Go to the center of the bed (400x400)
G1 X250 Y250 F10000    ; Go to the center of the bed (500x500)
G30                     ; Home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91                     ; Relative positioning
G1 Z5 F100              ; Lift Z relative to current position
G90                     ; Absolute positioning