Posts made by Benny

@phaedrux 3.2 i think , blue red and green.
yes Ive got multiple AP's on there.

@phaedrux yea 3.3
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Thu Oct 22 2020 17:33:54 GMT+0100 (British Summer Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"HevORT" ; set printer name
M669 K1 ; select CoreXY mode

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
;BED LEVEL
M671 X-30:330 Y200:200 S6

; Drives
M569 P0 S0 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P4 S0
M569 P5 S1 ; physical drive 5 goes forwards

M584 X0 Y1 Z2:4 E3:5 ; set drive mapping

M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E397.28:419.00 ; set steps per mm
M566 X1500.00 Y1500.00 Z105.00 E900.00:3000.00 ; set maximum instantaneous speed changes (mm/min)
M203 X30000.00 Y30000.00 Z1200.00 E10000.00:18000.00 ; set maximum speeds (mm/min)
M201 X9000.00 Y9000.00 Z120.00 E4000.00:2000.00 ; set accelerations (mm/s^2)
M906 X1200 Y1200 Z1000 E1100:1000 I30 ; set motor currents (mA) and motor idle factor in per cent
;M593 F34.2
M84 S30 ; Set idle timeout

;M566 X400 Y400 Z8 C2 E2:2:2:2 ; Set maximum instantaneous speed changes (mm/min)
;M203 X35000 Y35000 Z1200 C5000 E5000:5000:5000:5000 ; Set maximum speeds (mm/min)
;M201 X6000 Y6000 Z400 C500 E2500:2500:2500:2500 ; Set accelerations (mm/s^2)
;M906 X1800 Y1800 Z1330 I30 ; Idle motion motors to 30%

; Axis Limits
M208 X-30 Y0 Z-5 S1 ; set axis minima
M208 X280 Y280 Z300 S0 ; set axis maxima

; Endstops
M574 X1 S3 ; configure sensorless endstop for low end on X
M574 Y1 S3 ; configure sensorless endstop for low end on Y
M574 Z1 S2 ; configure Z-probe endstop for low end on Z

; Z-Probe
M950 S0 C"duex.pwm1" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T10000 ; set Z probe type to bltouch and the dive height + speeds
G31 P25 X60 Y-10 Z2.45 ; set Z probe trigger value, offset and trigger height
M557 X80:280 Y20:280 S60 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 R4700 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 Q10 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S140 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 S"BMG" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
M563 P1 S"TITAN" D1 H1 F0 ; define tool 1
G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0 ; select first tool
M564 H0

@jay_s_uk
m115

FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.3 ELECTRONICS: Duet WiFi 1.02 or later + DueX5 FIRMWARE_DATE: 2021-06-15 21:45:03

m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DGM-9T6BU-FG3SN-6JKD0-3S86K-9AZVF
Used output buffers: 3 of 24 (14 max)
=== RTOS ===
Static ram: 23876
Dynamic ram: 76072 of which 12 recycled
Never used RAM 14456, free system stack 112 words
Tasks: NETWORK(ready,14.2%,236) HEAT(delaying,0.0%,208) Move(notifyWait,0.2%,309) DUEX(notifyWait,0.0%,24) MAIN(running,85.3%,420) IDLE(ready,0.3%,29), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:20:22 ago, cause: software
Last software reset at 2021-08-02 19:06, reason: User, GCodes spinning, available RAM 14456, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x10
Step timer max interval 0
MCU temperature: min 39.0, current 41.4, max 41.8
Supply voltage: min 24.0, current 24.3, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, SG min/max 0/1023
Driver 1: position 0, standstill, SG min/max 0/1023
Driver 2: position 22271, standstill, SG min/max 0/107
Driver 3: position 0, standstill, SG min/max 0/1023
Driver 4: position 0, standstill, SG min/max 0/102
Driver 5: position 0, standstill, SG min/max not available
Driver 6: position 0, standstill, SG min/max not available
Driver 7: position 0, standstill, SG min/max not available
Driver 8: position 0, standstill, SG min/max not available
Driver 9: position 0, standstill, SG min/max not available
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-08-02 19:26:56
Cache data hit count 4294967295
Slowest loop: 220.39ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.9ms, write time 409.6ms, max retries 0
=== Move ===
DMs created 83, maxWait 218101ms, bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves 471, completed moves 471, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 48], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== DueX ===
Read count 1, 0.05 reads/min
=== Network ===
Slowest loop: 413.84ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• WiFi -
  Network state is active
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.26
  WiFi MAC address 84:f3:eb:42:b0:cb
  WiFi Vcc 3.36, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 25600
  WiFi IP address 192.168.50.163
  WiFi signal strength -43dBm, mode 802.11n, reconnections 0, sleep mode modem
  Clock register 00002002
  Socket states: 0 0 0 0 0 0 0 0

@jay_s_uk said in Can't use emergency stop button after update:

M552 S1

Yea thats in there, wifi 1.4
I've had it years now

@jay_s_uk It used to come back on after

The emergency stop button in web control causes wifi to turn off or something blue light just blinks.
the only way to get it back on is to power usb, And it instantly recovers.
Any help would be appreciated.
cheers
Ben

Try to get rid of crimps and keep single insulated cables down to a minimum, with mains cables.

make sure you have m501 in config, and m500 after autotune

No worries think I have sorted, Reset everything, deleted cache and repaired sd card.
Not sure what fixed it.

I am having the same problem, just started out of nowhere.
worked perfect for months, 3 days after installing RRF3 having problems.

This is my home all that works perfect

; homeall.g

; Endstops
M574 X1 S3 F0 R0 ; Set active High endstops (S1=SENSORED) (X-MIN(1)) (S3=SENSORLESS)
M574 Y2 S3 F0 R0 ; Set active High endstops (S1=SENSORED) (Y-MIN(1)) (S3=SENSORLESS)
M915 X Y S3 R0 F0 ; set X and Y to sensitivity 5, do nothing when stall, unfiltered
M400

M201 X500 Y500 Z50:50 E500 ; Set accelerations (mm/s^2) 500,500

;Home Y First
M400 ; make sure everything has stopped before we make changes
M913 X50 Y50 ; reduce motor current to 50% to prevent belts slipping
G91 ; relative positioning
G1 Z5 F4800 S2 ; lift Z relative to current position
G4 P500 ; wait 500msec
G1 S1 Y430 F4800 ; move quickly to X or Y endstop and stop there (first pass)
G4 P500 ; wait 500msec
G1 Y-10 ; Move Away 20mm X axis
G4 P500 ; wait 500msec
;G1 Z-5 F6000 S2 ; lift Z relative to current position
;G90 ; absolute positioning
;M400 ; make sure everything has stopped before we reset the motor currents
;M913 X100 Y100 ; motor currents back to normal

; Home X Second
M400 ; make sure everything has stopped before we make changes
;M913 X50 Y50 ; reduce motor current to 40% to prevent belts slipping
;G91 ; relative positioning
;G1 Z5 F4800 S2 ; lift Z relative to current position
;G4 P500 ; wait 500msec
G1 S1 X-305 F4800 ; move quickly to X or Y endstop and stop there (first pass)
G4 P500 ; wait 500msec
G1 X10 ; Move Away 10mm X axis
;G4 P500 ; wait 500msec
;G1 Z-5 F6000 S2 ; lift Z relative to current position
G90 ; absolute positioning
M400 ; make sure everything has stopped before we reset the motor currents
M913 X100 Y100 Z100 ; motor currents back to normal

G1 X150 Y150 F6000 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed
;M915 P0 S4 R0 F1 H300
;M915 P1 S4 R0 F1 H300
;Stall Detection
M915 X Y S5 F0 H400 R4700 ; X / Y Axes

;M201 X2000 Y2000 Z100 E9000
M566 X600 Y600 Z24 E500 ; Set maximum instantaneous speed changes (Jerk) (mm/min)
;M203 X20000 Y20000 Z500 E3600 ; Set maximum speeds (mm/min)
;M201 X3000 Y3000 Z200 E1000 ; Set accelerations (mm/s^2)

;testing
;M566 X400 Y400 Z8 E2 ; Set maximum instantaneous speed changes (mm/min)
M203 X35000 Y35000 Z1200 E5000 ; Set maximum speeds (mm/min)
M201 X6000 Y6000 Z400 E2500 ; Set accelerations (mm/s^2)

Was just the driver for me, dc42 told me to remove plastic molex near by becuase they will get crispy.
150c hot air will get them off slowly with pliers.
Find my post there is info that will help you there.

https://uk.farnell.com/trinamic/tmc2660-pa/motor-driver-stepper-qfp-44/dp/2822176

I done mine, and I'm rubbish at soldering.
Hot air station is recommended

Yea the doubles are easy its the single small ones between them.

@dc42
The problem I'm having is bridging, through lack of experience, then using wick to remove bridge and probably the solder under pins. Trying to find the balance

@dc42
Changed driver having problems with B phase, alert pops up says B phase may be disconnected but motor works.
Any Clues what I've done wrong ?

@dc42 thank you for your reply hope you have had a good Christmas.
Do i need hot plate or will it work just as well with just hot air ?

@dc42 whats the best way to remove old driver ?
Thanks Ben

@dc42 I feel slightly better knowing you have done it too.
I'm just glad it was just the driver not the whole board, no printing till after Xmas probably a good thing as it drives everyone mad.