Hi,
I'm trying to configure a multiple bed heaters setup, however i'm not succeeding in getting the bed heaters to show up in the DWC and Paneldue.
My specific heater config looks like :
; Heaters___________________________________________________________
; Bed1 parameters
M140 P0 H0
M305 P3 S"Bed1" X150 T"J" ; Set thermocouple heater 0 = bed 1 thermocouple = J type
M143 H0 S125 ; Set temperature limit for heater 0 to 125C
; Bed2 parameters
M140 P3 H6
M305 P3 S"Bed2" X151 T"J" ; Set thermocouple heater 0 = bed 1 thermocouple = J type
M307 H6 B1 S1.00
M143 H6 S125 ; Set temperature limit for heater 0 to 125C
; Bed3 parameters
M140 P4 H7
M305 P3 S"Bed3" X152 T"J" ; Set thermocouple heater 0 = bed 1 thermocouple = J type
M307 H6 B1 S1.00
M143 H6 S125 ; Set temperature limit for heater 0 to 125C
;E0_________________________________________________________________
M305 P1 T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S285 ; Set temperature limit for heater 1 to 285C
;E1_________________________________________________________________
M305 P2 T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 2
M143 H2 S285 ; Set temperature limit for heater 2 to 285C
and for completion, the complete config looks like :
; General preferences_______________________________________________
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M111 S0 ; Debug off
M555 P2 ; Set output to look like Marlin
M575 P1 B57600 S1 ; Set auxiliary serial port baud rate and require checksum (for PanelDu
; Network________________________________________________________ֹֹֹֹֹ___
M550 P"Big Meter - Kverneland Group" ; Set machine name
;M551 P"MODIX3D" ; Set password (optional)
M552 S1 ; Enable network
;M552 P0.0.0.0 ; Uncomment this command for using Duet Ethernet board
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet
; Drives
;Main board______________________________________________________________________
M569 P0 S0 ; Physical drive 0 . X1
M569 P1 S1 ; Physical drive 1 . X2
M569 P2 R-1 ; Physical drive 2 . Canceled
M569 P3 S1 ; Physical drive 3 . Main Extruder
M569 P4 S0 ; Physical drive 4 . Secondery Extruder
;Duex5 board_____________________________________________________________________
M569 P5 S0 ; Physical drive 5 . Y
M569 P6 S0 ; Physical drive 6 . Z1 (0,1000)
M569 P7 S0 ; Physical drive 7 . Z2 (0,0)
M569 P8 S0 ; Physical drive 8 . Z3 (1000,0)
M569 P9 S0 ; Physical drive 9 . Z4 (1000,1000)
;___________________________________________________________________
M584 X0:1 Y5 Z6:7:8:9 U1 E3:4 P3 ; Driver mapping
M671 X-181:-181:1049:1049 Y1066:-58:-58:1066 S10 ; Anticlockwise
;___________________________________________________________________
M350 X16 Y16 Z16 E16:16 U16 I1 ; Configure microstepping with interpolation
M92 X100.00 Y100.00 Z2000.00 E440.530:418.500 U100.00 ; Set steps per mm
M566 X240 Y360 Z30.00 E120.00:120.00 U240 P1 ; Set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z200.00 E1200.00:1200.00 U9000.00 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z120.00 E250.00:250.00 U1000 ; Set accelerations (mm/s^2)
M204 P500 ; Set print and travel accelerations (mm/s^2)
M906 X1800 Y1800.00 E1000.00:1000.00 U1800 I40 ; Set motor currents (mA) and motor idle factor in per cent
M906 Z1800.00 I50 ; Set motor currents (mA) and motor idle factor in per cent
M84 S60 X Y U E0 E1 ; Set idle timeout - one minute
; Axis Limits_______________________________________________________
M208 X0:1000 Y0:1000 Z0:1000 U0:1000 ; Set axis minima and maxima
; Endstops__________________________________________________________
M574 X1 Y2 U1 S1 ; Set active low and disabled endstops
; Z-Probe___________________________________________________________
M574 Z2 S2 ; Set endstops controlled by probe
M307 H7 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch
M558 P9 H5 F120 T9000 A1 R0.7 ; Set Z probe type to bltouch and the dive height + speeds
G31 P500 X-14 Y21 Z1.284 ; Set Z probe trigger value, offset and trigger height(Z-Offset)
M557 X-14:974 Y21:1009 S52 ; Define mesh grid. 400 Points
M376 H30 ; Height (mm) over which to taper off the bed compensation
; Heaters___________________________________________________________
;M140 H-1 ; Disable heated bed
;M307 H0 A-1 C-1 D-1 ; Disable heater on PWM channel
; Bed1 parameters
M140 P0 H0
M305 P3 S"Bed1" X150 T"J" ; Set thermocouple heater 0 = bed 1 thermocouple = J type
M143 H0 S125 ; Set temperature limit for heater 0 to 125C
; Bed2 parameters
M140 P3 H6
M305 P3 S"Bed2" X151 T"J" ; Set thermocouple heater 0 = bed 1 thermocouple = J type
M307 H6 B1 S1.00
M143 H6 S125 ; Set temperature limit for heater 0 to 125C
; Bed3 parameters
M140 P4 H7
M305 P4 S"Bed3" X152 T"J" ; Set thermocouple heater 0 = bed 1 thermocouple = J type
M307 H6 B1 S1.00
M143 H6 S125 ; Set temperature limit for heater 0 to 125C
;E0_________________________________________________________________
M305 P1 T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S285 ; Set temperature limit for heater 1 to 285C
;M307 H1 A# C# D# V# S1.0 B0 ; PID calibration
;E1_________________________________________________________________
M305 P2 T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 2
M143 H2 S285 ; Set temperature limit for heater 2 to 285C
;M307 H2 A# C# D# V# S1.0 B0 ; PID calibration
; Fans______________________________________________________________
M106 P0 S0 I0 F500 H-1 C"E0 BlowerFan" ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0 I0 F500 H-1 C"E1 BlowerFan" ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P5 T46 H1 ; Set fan 5. Thermostatic control is turned on
M106 P6 T46 H2 ; Set fan 6. Thermostatic control is turned on
M106 P2 I-1 ; LED (optional)
M106 P3 I-1 ; LED (optional)
M106 P4 I-1 ; LED (optional)
M106 P7 I-1 ; Main LED
M106 P8 I-1 ; LED (optional)
; Tools
;T0_________________________________________________________________
M563 P0 S"E0 Primary" D0 H1 F0 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S210 ; Set initial tool 0 active and standby temperatures to 0C
;T1_________________________________________________________________
M563 P1 S"E1 Secondary" D1 H2 F1 ; Define tool 1
G10 P1 X0 Y49 Z0 ; Set tool 1 axis offsets
G10 P1 R0 S210 ; Set initial tool 1 active and standby temperatures to 0C
; Automatic power saving____________________________________________
M911 S22.5 R29.0 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss. Power Failure Pause
; Custom settings___________________________________________________
M591 D0:1 P1 C4 S1 ; Regular filament sensor for E0 and E1
;M564 H0 S0 ; Negative movements are allowed
Bed heater 2 and 3 don't appear in the DWC and Paneldue( bed heater H0 does ).
Looking at the diagnostics ( M122 ), the heaters seem to be correctly defined
=== Bed heaters = 0 -1 6 7
What am i doing wrong? Why are they not displayed? Giving them a name ( as noted in the docs M305 S parameter ) does not seem to help unfortunately.
