Thank you so much! you guys ROCK
Posts made by amjm22
-
RE: Error: M950: exactly one of FHJPSR must be given
-
Error: M950: exactly one of FHJPSR must be given
Error: M950: exactly one of FHJPSR must be given
Board: Duet 3 Mini 5+ (Mini5plus)
DSF Version: 3.4.6
Firmware: RepRapFirmware for Duet 3 Mini 5+ 3.4.6 (2023-07-21)
Here is my config file.Can you please assist? config (2).g
-
RE: Orbiter 2 extruder mounting for Smart effector with Magball arms
Here is what I am using with my Smart Effector.
-
RE: firmware 3.4 Rc1 Heater Fault
@massimilianoconti said in firmware 3.4 Rc1 Heater Fault:
M307 H1 R2.558 K0.275:0.103 D6.31 E1.35 S1.00 B0 V23.9
Have you tried bumping up the "deadtime" D6.31? I bumped mine up to D8.31 and the heat faults have gone away.
-
Firefox - DWC strange characters appear
Can someone please tell me what these strange tags are that just popped up when opening my web control for my printer?
Board: Duet 3 MB6HC (MB6HC)
DSF Version: 3.3.0
Firmware: RepRapFirmware for Duet 3 MB6HC 3.3 (2021-06-15)Thanks!
amjm22
-
RE: Extruder for DC/Kossel XL recommendations
I'm using an Orbiter 1.5 mounted to Duet 3D Smart Effector. It has a 58mm Bowden tube(very minimal) E3d .6 nozzle and all-metal hotend.
-
RE: Hints for accelerometer placeing
@dc42 Much appreciated! I will give it a shot when the accelerometer arrives! i post the results.
-
RE: Hints for accelerometer placeing
I have a Delta printer using a Duet smart effector, I'm using a Duet3d 6hc3 sys board.
Where would you mount an accelerometer to the smart effector?
Wiring is not the issue, it is the physical location.
-
RE: New stable firmware bundle 3.2 released
@amjm22 I did again and it worked! unreal
-
RE: New stable firmware bundle 3.2 released
@Phaedrux - sudo apt update/upgrade. I did that, I'm still on Duet Web Control 3.1.1
Thanks for your reply
-
RE: New stable firmware bundle 3.2 released
When installing The Webserver to 3.2 I get this error -
RepRapFirmware for Duet 3 MB6HC version 3.2 running on Duet 3 MB6HC v0.6 or 1.0 (SBC mode)
1/10/2021, 11:39:15 AM Failed to upload materialdesignicons-webfont.4187121a.woff2
Operation failed (Reason: Access to the path '/opt/dsf/sd/www/fonts/materialdesignicons-webfont.4187121a.woff2' is denied.)Has anyone seen this before?
-
RE: New stable firmware bundle 3.2 released
@dc42 Yes, it worked! Thanks
-
RE: New stable firmware bundle 3.2 released
@dc42 Thanks! I held my breath, restarted and it came back on... Things were touch and go for a moment!
I appreciate all of the support, You guys are amazing
-
RE: New stable firmware bundle 3.2 released
How long does it take to update the firmware? Mine has been going on for 40 minutes
-
RE: RRF 3.2 (possibly) related scare
How long does it take to update to ver 3.2
mine is still updating after 30 minutes.Please advise
Thanks