@alankilian it was as simple as adding a solid mount to the sensor. Now it works fine 
Best posts made by Alucardi
-
RE: Magnetic sensor reports negative min valueposted in Filament Monitor
-
RE: Duet 3 mini 5+ need help with wiring and configposted in Firmware installation
now it worked. M558 P9 still give same error though
"m558
Z Probe 0: type 9, input pin io3.in, output pin nil, dive height 350.0mm, probe speed 350mm/min, travel speed 4800mm/min, recovery time 0.00 sec, heaters suspended, max taps 1, max diff 0.03"G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Hevo" ; set printer name M669 K1 ; select CoreXY mode ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0.0 S1 D2 ; physical drive 0.0 goes forwards M569 P0.1 S1 D2 ; physical drive 0.1 goes forwards M569 P0.2 S1 D2 ; physical drive 0.2 goes forwards M569 P0.3 S1 D2 ; physical drive 0.3 goes forwards M569 P0.4 S1 D2 ; physical drive 0.4 goes forwards M584 X0.0 Y0.1 Z0.2:0.3 E0.4 ; set drive mapping M350 E16 I0 ; configure microstepping without interpolation M350 X16 Y16 Z8 I1 ; configure microstepping with interpolation M92 X160.00 Y160.00 Z1600.00 E407.00 ; set steps per mm M566 X380.00 Y380.00 Z20.00 E4000.00 ; set maximum instantaneous speed changes (mm/min) M203 X12000.00 Y12000.00 Z500.00 E4000.00 ; set maximum speeds (mm/min) M201 X1200.00 Y1200.00 Z300.00 E5000.00 ; set accelerations (mm/s^2) M906 X900 Y900 Z1200 E450 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z-0.5 S1 ; set axis minima M208 X330 Y343 Z450 S0 ; set axis maxima M671 X-45:380 Y170:170 S1 ; leadscrew positions ; Endstops M574 X1 S3 ; configure sensorless endstop for high end on X M574 Y2 S3 ; configure sensorless endstop for high end on Y M574 Z1 S2 ; configure Z-probe endstop for low end on Z ; Z-Probe M950 S0 C"io3.out" ; create servo pin 0 for BLTouch M558 P9 C"^io3.in" H350 F350 T4800 B1 ; set Z probe type to bltouch and the dive height + speeds + heater off while probing G31 P500 X25 Y-20 Z0.85 ; set Z probe trigger value, offset and trigger height M557 X25:310 Y25:310 P6 ; define mesh grid + Probe points ; Heaters M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0 M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0 M307 H0 B0 S0.70 ; disable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M308 S1 P"temp1" Y"thermistor" T500000 B4723 C1.19622e-7 ; configure sensor 1 as thermistor on pin temp1 M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1 M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit M143 H1 S350 ; set temperature limit for heater 1 to 350C ; Fans M950 F0 C"out5" Q50 ; create fan 0 on pin out5 and set its frequency M106 P0 C"Hotend fan " S0 H1 T50 ; set fan 0 name and value. Thermostatic control is turned on M950 F1 C"out6" Q1000 ; create fan 1 on pin out6 and set its frequency M106 P1 C"Blower" S0 H-1 ; set fan 1 name and value. Thermostatic control is turned off ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined ; Miscellaneous M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss -
RE: Sensorless homing issuesposted in Tuning and tweaking
Have you dsone this?
"You need to run the stealthChop tuning procedure first. You can do this is the homing files.This is what I suggest:
Execute a tiny move (1 or 2 microsteps) away from the homing direction.
Pause for 100ms using G4.
Execute a small move away from the homing direction, e.g. 10mm.
Execute the homing move.
Don't forget to reduce current for the homing move (M913)." -
RE: One z motor don’t always moveposted in Duet Hardware and wiring
@droftarts firmware is 2.05.1
I will try your suggestions tonight. I know I could run of same driver but if it’s a defective drive I would still get it fixed but let’s hope it’s just firmware and nothing else. -
RE: Magnetic sensor reads sensitivy wrong.posted in Filament Monitor
@alankilian top of the axel looks rough but seems to be ok.
-
RE: Sensorless homing issuesposted in Tuning and tweaking
@tomkamin I cant find a calibration rutin for stealthchop in your homeall. You are also doing 2 passes which are only needed for switches. Here are my homeall.g that works for me with my mini 5+. I know it is messy, i need to clean this up but it works atleast.
M400 ; finishes all current moves and and thus clears the buffer
M913 X60 Y60 ; drop motor current to 33%
M569 P0.0 D3 V60 ; reduce V to ensure stealthChop is enabled
M569 P0.1 D3 V60 ; reduce V to ensure stealthChop is enabled
M915 P0 S0 R0 F0 H400 ; sensitivity X, don’t take action, don’t filter -4
M915 P1 S0 R0 F0 H400 ; sensitivity Y, don’t take action, don’t filter -4
M400 ; finishes all current moves and and thus clears the buffer
G91 ; relative positioning
G1 H1 Z10 F5000 ; lift Z relative to current position
G1 H1 X5
G4 P300
G1 H1 X20 F3000
G1 H1 X-400 F3000 ; move to X
G1 H1 Y-5
G4 P200
G1 H1 Y-20 F3000
G1 H1 Y400 F3000 ; move to Y
M913 X100 Y100 ; return current to 100%
G90 ; absolute positioning
G1 X167.5 Y167.5 F5000
G30 ; home Z by probing the bed
M402 ; retract probe
G1 Z5 F5000
M400 ; finishes all current moves and and thus clears the buffer
M569 P0.0 D2 ; restore default for motor
M569 P0.1 D2 ; restore default for motor
M913 X100 Y100 ; return current to 100%
M400 ; finishes all current moves and and thus clears the buffer -
RE: Magnetic sensor reads sensitivy wrong.posted in Filament Monitor
@alankilian added paper between the housings and that seem to have done the trick.
You happen to know if it is possible to calibrate e-steps with this?