Posts made by agent0810

@jumpedwithbothfeet

hey guys, so my buddy just put a BLtouch on his non duet board and he had to set the touch to probe before the print then save the points it pulled to get the first layer, here is the gcode he used.

do we need to do something like that?

G28 ; home all axes
G1 Z10 F600 ; raise Z axis
M190 S[bed0_temperature] ; stabilize bed
M109 S[extruder0_temperature] ; stabilize extruder
G1 X5 Y10 Z0.2 F3000 ; move to wait position
G28; Home all axes
G29; bed leveling
M500; Store bed settings
G92 E0 ; reset extrusion distance
G1 E90 F1500 ; load filament
G92 E0 ; reset extrusion distance
G1 X160 E15 F600 ; prime nozzle
G1 X180 F5000 ; quick wipe

@Phaedrux

I reprinted the mount, this was for the ender 3 but fits okay on my ender 5.

I have taped a white paper and the results were the same as without it.

What you see in the picture is as close as I can get it withought having th nozzle drag on the glass. I can use the baby steps during a print to move it but when I remove that amount in my config it makes no difference.

@Phaedrux

Of course.

@Phaedrux I’m not sure my probe is working correctly, no matter what I do it either eaves the nozzle to far from the bed (this is 85% of the time) or it is way to close and no filament comes out. Should I try moving the probe up a tad bit?

I checked the squareness of the frame when I put it together and thought it was pretty damn good.

@JoergS5

i have went around multiple points on the bed and done the paper trick to get the bed as level as i think i possible can. advice on how to get it more accurate? thank you!

@Phaedrux

got it to finally work, but it looks worse lol

@jumpedwithbothfeet

hey guys, sorry for the delay, got sick and was having a down system at work.

so i set it back to:
M557 X10:175 Y10:215 P8

and here is what i get:

8/3/2020, 12:02:36 PM M29
GCode end-of-file being interpreted.

@JoergS5 soooooo i need a new bed?

@JoergS5 hmmmmm when i untighten the screws the bed goes up, when i tighten its pulled down.

@JoergS5

not sure what you mean int the xy but not the z direction

@JoergS5
yea i try to do this all when the bed is heated. its a ender 5 pro so it has 4 big black screws on the bottom.

@JoergS5
ive kinda gone over that as much as i can. all the bars seem to be level and parallel to the bed. im not sure what i could be doing wrong. i ve read alot of artices, alot of advice and help from people here, and youtube videos. i just cant seem to get it leveled .....

@JoergS5 thank you for the help!

@JoergS5 well that helped a bit. :). .... any other recomendations?

@JoergS5 so something like X50:175?

@Phaedrux

done. thank you again for all your help.

https://forum.duet3d.com/topic/17871/issues-with-ir-probe-offset

New ir probe installed and having issues with the offset, when i try to print the nozzle drags along the bed. I have Done all i can from the test and calibrate the z probe without luck. I am running the duet 2 wifi on my ender 5 pro, here are my files:

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Sun Jul 05 2020 20:32:26 GMT-0500 (Central Daylight Time)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"Schaal3DPrinter"                            ; set printer name

; Network
M552 S1                                            ; enable network
M586 P0 S1                                         ; enable HTTP
M586 P1 S1                                         ; enable FTP
M586 P2 S1                                         ; enable Telnet

; Drives
M569 P0 S0                                         ; physical drive 0 goes forwards
M569 P1 S0                                         ; physical drive 1 goes forwards
M569 P2 S0                                         ; physical drive 2 goes forwards
M569 P3 S0                                         ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E130                   ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00            ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30                       ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X225 Y225 Z300 S0                             ; set axis maxima

; Endstops
M574 X2 S1 P"xstop" 							   ; configure active-high endstop for low end on X via pin xstop
M574 Y2 S1 P"ystop" 							   ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop"                                ; configure active-high endstop for high end on Z via pin zstop

; Z-Probe
M558 P1 C"^zprobe.in" H5 F120 T6000                 ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X-50 Y0 Z0.195                              ; set Z probe trigger value, offset and trigger height
M557 X10:175 Y10:215 P8                           ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138     ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                              ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00                                   ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                            ; map heated bed to heater 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138      ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                               ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit

; Fans
M950 F0 C"fan0" Q500                               ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                     ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                               ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                                  ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                                   ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
M501

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Sun Jul 05 2020 20:32:27 GMT-0500 (Central Daylight Time)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X+250 Y+250 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X-5 Y-5 F6000 ; go back a few mm
G1 H1 X+230 Y+230 F360 ; move slowly to X and Y axis endstops once more (second pass)
G90 ; absolute positioning
G1 X150 Y150 F6000 ; move probe to center of bed
G30 ; probe the bed
;G1 H1 Z305 F360 ; move Z up stopping at the endstop
;G1 H1 Z-320 F360 ; move Z  stopping at the endstop
;G90 ; absolute positioning

; Uncomment the following lines to lift Z after probing
;G91                    ; relative positioning
;G1 Z5 F100             ; lift Z relative to current position
;G90                    ; absolute positioning

; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Sun Jul 05 2020 20:32:27 GMT-0500 (Central Daylight Time)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X+250 F1800 ; move quickly to X axis endstop and stop there (first pass)
G1 H2 X-5 F6000 ; go back a few mm
G1 H1 X+230 F360 ; move slowly to X axis endstop once more (second pass)
G1 H2 Z-5 F6000 ; lower Z again
G90 ; absolute positioning

; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Sun Jul 05 2020 20:32:27 GMT-0500 (Central Daylight Time)
G91              ; relative positioning
G1 H2 Z5 F6000   ; lift Z relative to current position
G90 ; absolute positioning
G1 X150 Y150 F6000 ; move probe to center of bed
G30 ; probe the bed
;G1 H1 Z305 F1800 ; move Z up until the endstop is triggered
;G1 H1 Z-320 F360 ; move Z  stopping at the endstop
;G90 ; absolute positioning

; Uncomment the following lines to lift Z after probing
;G91             ; relative positioning
;G1 Z5 F100      ; lift Z relative to current position
;G90             ; absolute positioning

; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Sun Jul 05 2020 20:32:27 GMT-0500 (Central Daylight Time)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 Y+230 F1800 ; move quickly to Y axis endstop and stop there (first pass)
G1 H2 Y-5 F6000 ; go back a few mm
G1 H1 Y+230 F360 ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F6000 ; lower Z again
G90 ; absolute positioning

7/28/2020, 5:18:15 PM	M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
Board ID: 08DLM-996RU-N8PS4-7J1FJ-3SJ6S-189BQ
Used output buffers: 3 of 24 (12 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 93932 of which 44 recycled
Exception stack ram used: 568
Never used ram: 8548
Tasks: NETWORK(ready,384) HEAT(blocked,1224) MAIN(running,1840) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:50:08 ago, cause: software
Last software reset at 2020-07-28 16:28, reason: User, spinning module GCodes, available RAM 8852 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 30.2, current 31.0, max 31.9
Supply voltage: min 23.9, current 24.1, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 0/324
Driver 1: standstill, SG min/max 87/298
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-07-28 17:18:11
Cache data hit count 4294967295
Slowest loop: 17.01ms; fastest: 0.12ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 4.1ms, write time 2.1ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 166, MaxWait: 139149ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 348, completed moves: 348, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 80.05ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address bc:dd:c2:2d:67:97
WiFi Vcc 3.39, reset reason Unknown
WiFi flash size 4194304, free heap 21240
WiFi IP address 10.1.2.149
WiFi signal strength -53dBm, reconnections 0, sleep mode modem
Socket states: 4 0 0 0 0 0 0 0

7/27/2020, 8:02:10 PM	Upload of config.g successful after 0s
7/27/2020, 8:01:37 PM	G30 S-1
Stopped at height 0.195 mm
7/27/2020, 8:01:23 PM	G1 Z5
7/27/2020, 8:01:14 PM	G30 S-1
Stopped at height 0.196 mm
7/27/2020, 8:00:58 PM	G1 Z5
7/27/2020, 8:00:45 PM	G30 S-1
Stopped at height 0.195 mm
7/27/2020, 8:00:25 PM	G1 Z5
7/27/2020, 7:59:46 PM	G30 S-1
Stopped at height 0.192 mm

@Phaedrux

why do i get the feeling this isnt good lol

@Phaedrux
alright ill give that a shot. see what happens. thank you

@Phaedrux
sorry, just new to this and trying to take in a lot, im def a noob.

so would this be right:

M557 X-50:165 Y15:195 S20 ?