BL Touch issues
-
@bpislife I actually used that guide first, but when it wasn't working properly I went back to the duet guide and tried that.
I'm using the Duet Wifi -- I just bought it new a month ago from Filastruder.
deployprobe.g:
; deployprobe.g
; called to deploy a physical Z probe
;
; generated by RepRapFirmware Configuration Tool on Sun Jul 29 2018 11:50:39 GMT-0400 (Eastern Daylight Time)
M280 P3 S10 I1retractprobe.g:
; retractprobe.g
; called to retract a physical Z probe
;
; generated by RepRapFirmware Configuration Tool on Sun Jul 29 2018 11:50:39 GMT-0400 (Eastern Daylight Time)
M280 P3 S90 I1 -
@kskiff7034 Ok, so can you double check that you have yellow plugged into Heater3 (pin 8 ) on the large header? If so, can you send this command in the console: "M280 P3 S10 I1"
-
As for wiring, I have it set up exactly as it appears in this picture:
https://d17kynu4zpq5hy.cloudfront.net/igi/duet3d/KUDxTZSs3rnd3JVH.standard
I also tried the other version of setup from the guide that you posted using Heater 7 (Pin 31).
-
@kskiff7034 Ok. Did you cut the 5V line on the back of the bltouch? Also did you send that command manually to the bltouch?
-
I did cut the 5v line, but like I said in the original post I can't really tell if it's actually "cut". I used an xacto blade and ran over it quiet a few times, but it's so small you can't really see it. And yes, I sent it manually in the duet browser window in G-Code Console. I've also tried using a macro.
-
This post is deleted! -
I have a multimeter but I'm not very experience with it. I've used it a handful of times to test different things but wasnt sure how to do so on the BL touch.
-
@kskiff7034 Take a resistance measurement across the two exposed pads (on either side of your cut). The resistance should be large.
-
This'll take awhile. Getting the BL touch off is kind of a pain. Will report back in a bit.
-
@kskiff7034 Ok. It can be frustrating at first. It took me several hours the first time to figure out everything I was doing wrong. I have 4 of them working on my various printers. While its apart triple check your connection, your crimps, etc.
-
@bpislife So with the multimeter set to 200, touching the 2 pads causes the numbers to jump around wildly before settling on .4 for a few seconds and then dropping to .3
-
Setting it to 2000, 20k, 200k, and 20m cause it to jump around wildly before settling at 0, but setting it to 200m it settles at .9? So confused.
-
Ok so I'm having doubts about whether I cut the pcb trace correctly.
Looking at this image:
Am I supposed to cut the little line between the two pads, or one of the lines near 5 or 6? I thought it was the line between the two pads, but now I'm not sure.
-
between the two pads.
-
Hm okay that's what I attempted to do, but maybe I didn't succeed? I don't want to keep sawing away at it though. Sigh.
-
can you take a picture of your wiring. I think you have it wired wrong. I just set one of these up last weekend and it was a breeze.
How are the lights blinking on the bl touch.....
-
Do you know how to use a multimeter?
.4 doesn’t tell me anything.. .4ohms is very low. At 200ohms, i would expect it to read OL
-
You need to turn th multimeter to the thing that sorta looks like a horseshoe.
-
There are no blinking lights. When I turn it on, it runs the test and deploys and retracts the pin twice.
Image is a little deceiving. The red/black wire were combined into one and I split them, so there is still a bit of red on the black wire.
-
hi. That shows three of the wires. what about the other two?
