Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Duet2 wifi stuck repeating Wifi Error.

    Scheduled Pinned Locked Moved Unsolved
    Duet Hardware and wiring
    6
    65
    1.6k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • zBeebleundefined
      zBeeble
      last edited by

      So... been printing OK... for awhile. Just started acting up today again. Oddly, the serial output is "chunky" .... and incomplete. One recent query:

      m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.5.1 (2024-04-19 14:40:46) running on Duet WiFi 1.02 or later
Board ID: 08DDM-9FAM2-LW4SD-6J9F8-3SN6J-T3ZRY
Used output buffers: 1 of 26 (26 max)
=== RTOS ===
Static ram: 23256
Dynamic ram: 72928 of which 12 recycled
Never used RAM 13540, free system stack 110 words
Tasks: NETWORK(1,ready,15.7%,175) HEAT(3,nWait 5,0.1%,307) Move(4,nWait 5,2.9%,298) MAIN(1,running,81.3%,711) IDLE(0,ready,0.0%,
29), total 100.0%
Owned mutexes: WiFi(NETWORK) USB(MAIN)
=== Platform ===
Last reset 10:03:58 ago, cause: power up
Last software reset at 2024-07-29 10:46, reason: User, Gcodes spinning, available RAM 17140, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x04
Aux0 errors 0,0,0
MCU temperature: min 35.4, current 35.9, max 36.9
Supply voltage: min 11.0, current 12.2, max 12.3, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/6, heap memory allocated/used/recyclable 2048/932/816, gc cycles 1
Events: 0 queued, 0 completed
Driver 0: ok, SG min 0
Driver 1: ok, SG min 0
Driver 2: ok, SG min 0
Driver 3: ok, SG min 0
Driver 4: standstill, SG min n/a
Driver 5:
Driver 6:
Driver 7:
Driver 8:
Driver 9:
Driver 10:
Driver 11:
Date/time: 2024-07-30 01:04:58
Cache data hit count 4294967295
Slowest loop: 11.10ms; fastest: 0.20ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.5ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 23, maxWait 448ms, bed compensation in use: mesh, height map offset -0.031, max steps late 0, m
in interval 0, bad calcs 0, ebfmin 0.00, ebfmax 1.00
next step interrupt due in 20 ticks, disab
      1 Reply Last reply Reply Quote 0
      • zBeebleundefined
        zBeeble
        last edited by

        Notably, on one output not shown, "slowest loop" was around 146ms.

        1 Reply Last reply Reply Quote 0
        • zBeebleundefined
          zBeeble
          last edited by

          I've turned on the debugging for 14 and 1 (wifi and network). Lots of chatter, but the printer is definitely acting up. The serial is no longer chunky, but at one point, I disconnected the serial ... which would reset the driver on the server.... and probably the duet, too.

          m111 and chatter look like:

          Debugging enabled for modules: Network(1 - 0xffffffff) WiFi(14 - 0xffffffff)
Debugging disabled for modules: Platform(0) Webserver(2) Gcodes(3) Move(4) Heat(5) Kinematics(6) InputShaping(7) unused(8) Print
Monitor(9) Storage(10) PortControl(11) DuetExpansion(12) FilamentSensors(13) Display(15) SbcInterface(16) CAN(17) Expansion(18)
New conn on socket 0 for local port 80
Found responder
Received 367 bytes
New conn on socket 1 for local port 80
Found responder
Received 329 bytes
New conn on socket 0 for local port 80
Found responder
New conn on socket 1 for local port 80
Found responder
Received 329 bytes
Received 367 bytes
New conn on socket 0 for local port 80
          1 Reply Last reply Reply Quote 0
          • Phaedruxundefined Phaedrux marked this topic as a question
          • Phaedruxundefined
            Phaedrux Moderator
            last edited by

            Have you tried updating to 3.5.2 yet? Or the 3.6 alpha release? I think the beta is upcoming as well.

            Z-Bot CoreXY Build | Thingiverse Profile

            zBeebleundefined 1 Reply Last reply Reply Quote 0
            • zBeebleundefined
              zBeeble
              last edited by

              The printer was idle, so I shut off the constant network chatter. wifi debug was still on (as it's fairly quiet). During the idle day, it said this:

              Debugging enabled for modules: WiFi(14 - 0xffffffff)
Debugging disabled for modules: Platform(0) Network(1) Webserver(2) Gcodes(3) Move(4) Heat(5) Kinematics(6) InputShaping(7) unus
ed(8) PrintMonitor(9) Storage(10) PortControl(11) DuetExpansion(12) FilamentSensors(13) Display(15) SbcInterface(16) CAN(17) Exp
ansion(18)
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns

              Now.... 2 computers look at the web server and the web server is on an RFC 1918 address behind NAT ... so not general internet exposed.

              1 Reply Last reply Reply Quote 0
              • zBeebleundefined
                zBeeble @Phaedrux
                last edited by

                @Phaedrux said in Duet2 wifi stuck repeating Wifi Error.:

                Have you tried updating to 3.5.2 yet? Or the 3.6 alpha release? I think the beta is upcoming as well.

                I'm a little bit upgrade adverse ... you can convince me, but equally, I don't believe this is upgrade related.

                1 Reply Last reply Reply Quote 0
                • zBeebleundefined
                  zBeeble
                  last edited by

                  OOB ... looking at your debug message ... you could probably significantly cut binary size by cutting /home/renz/Projects from the path of all debug messages --- ie: cut to the root of the project.

                  1 Reply Last reply Reply Quote 0
                  • zBeebleundefined
                    zBeeble
                    last edited by

                    OK. Now it's full-on inaccessible.

                    Lots of these lines scrolling on the console.

                    ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
ResponseTimeout, pending=1
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
ResponseTimeout, pending=1
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
                    1 Reply Last reply Reply Quote 0
                    • zBeebleundefined
                      zBeeble
                      last edited by

                      And just to be clear, two local computers are pointing at it and no network traffic (as expected) is coming from the router for it.

                      1 Reply Last reply Reply Quote 0
                      • zBeebleundefined
                        zBeeble
                        last edited by

                        This is the log from the first few glitches above (posted here) through starting a new print and then it glitching hard:

                        Debugging enabled for modules: WiFi(14 - 0xffffffff)
Debugging disabled for modules: Platform(0) Network(1) Webserver(2) Gcodes(3) Move(4) Heat(5) Kinematics(6) InputShaping(7) unus
ed(8) PrintMonitor(9) Storage(10) PortControl(11) DuetExpansion(12) FilamentSensors(13) Display(15) SbcInterface(16) CAN(17) Exp
ansion(18)
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
Done printing file
Finished printing file 0:/gcodes/CFFFP_DeckStand_Anker.gcode, print time was 13h 4m
ResponseTimeout, pending=1
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseBusy
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
ResponseTimeout, pending=1
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
ResponseTimeout, pending=1
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
ResponseTimeout, pending=1
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
ResponseTimeout, pending=1
                        1 Reply Last reply Reply Quote 0
                        • zBeebleundefined
                          zBeeble
                          last edited by

                          I delivered m111 p1 s1, and this is the changed repeating output:

                          WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
1ResponseTimeout, pending=1
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Con^?/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578
): refused conn on port 80 already 4 conns
ResponseTimeout, pending=1
WiFi: /hom^?s/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
ResponseTimeout, pending=1
ResponseTimeout, pending=1
ResponseTimeout, pending=1

Debugging enabled for modules: Network(1 - 0xffffffff) WiFi(14 - 0xffffffff)
Debugging disabled for modules: Platform(0) Webserver(2) Gcodes(3) Move(4) Heat(5) Kinematics(6) InputShaping(7) unused(8) Print
Monitor(9) Storage(10) PortControl(11) DuetExpansion(12) FilamentSensors(13) Display(15) SbcInterface(16) CAN(17) Expansion(18)
ResponseTimeout, pending=1
Bad recv status size
ResponseTimeout, pending=1
Bad recv status size
ResponseTimeout, pending=1
Bad recv status size
ResponseTimeout, pending=1
Bad recv status size
ResponseTimeout, pending=1
Bad recv status size
WiFi: /home/renz/Projec^?/home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
ResponseTimeout, pending=1
Bad recv status size
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
ResponseTimeout, pending=1
Bad recv status size
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
ResponseTimeout, pending=1
Bad recv status size
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
ResponseTimeout, pending=1
Bad recv status size
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
ResponseTimeout, pending=1
Bad recv status size
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Con^?uet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on port 80 already 4 conns
ResponseTimeout, pending=1
Bad recv status size
WiFi: /home/renz/Projects/^?t 80 already 4 conns
ResponseTimeout, pending=1
Bad recv status size
WiFi: /home/renz/Projects/Duet3D/WiFiSocketServerRTOS/src/Connection.cpp(578): refused conn on po^?/Connection.cpp(578): refused conn on port 80 already 4 conns
ResponseTimeout, pending=1
Bad recv status size
ResponseTimeout, pending=1
Bad recv status size
                          1 Reply Last reply Reply Quote 0
                          • First post
                            Last post
                          Unless otherwise noted, all forum content is licensed under CC-BY-SA