FLY RRF E3 Sapphire Pro H0 not found Error

[kolbaskin]

Hi everyone

I have an issue with my Sapphire Pro with Fly E3 RRF Board and RepRap firmware installed.

H0 heater (bedheat) does not show up in a dashboard. When I try to heat it through console, an error "H0 not found" is showing up

Here is my configuration file:
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.10 on Sat Dec 05 2020 19:46:54 GMT+0100 (Central European Standard Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Kolbaskin" ; set printer name
M669 K1 ; select CoreXY mode

M929 S1

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S1 ; enable FTP
M586 P2 S1 ; disable Telnet
M575 P1 B57600 S1 ; Turn on PanelDue/RepPanel

; Drives
M569 P0 S0 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes forwards
M569 P3 S0 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
;M350 X32 Y32 Z32 E16 I1 ; configure microstepping with interpolation
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.30 Y80.30 Z1600.00 E392.40 ; set steps per mm
M566 X400.00 Y400.00 Z60.00 E100.00 P1 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z1200.00 E30000.00 ; set maximum speeds (mm/min)
M201 X2500.00 Y2500.00 Z200.00 E1000.00 ; set accelerations (mm/s^2)
M204 P2000 T4000 ; set acceleration for printing moves
M906 X1200 Y1200 Z1200 E1200 I50 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X223 Y220 Z235 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"!xstop"
M574 Y2 S1 P"!ystop"
M574 Z1 S1 P"!zstop" ; configure active-high endstop for low end on Z via pin zstop

; Z-Probe
M558 P1 C"zprobe.in" H5 F120 T6000 ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X15:215 Y15:195 S20 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as PT1000 on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H-1 ; set fan 1 value. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501 ; load saved parameters from non-volatile memory

;M593 F51 ; cancel ringing at 51Hz
;M572 D0 S0.7

Please help!

[jay_s_uk]

@kolbaskin bedheat isn't a valid pin name
https://teamgloomy.github.io/fly_e3_pins.html
Should be bed or hbed

[kolbaskin]

@jay_s_uk
Thank you
An issue has been solved