seeing if i can get assistance with bed connectins

[frnknstn]

@gixxerfast i have no fans under fan selection. thats where i assumed they would show up

[frnknstn]

@frnknstn ill double check and make sure i have the wires correct

[Gixxerfast]

@frnknstn That is strange, not even the tool fan? ... Is your config still as listed above ?

Try a M98 P"0:/sys/config.g" and check the console

[Gixxerfast]

@frnknstn You might want to uncomment your tool config at the end of config.g and end with a T0

[frnknstn]

@gixxerfast ; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves

; Network
M550 P"duet3" ; Set machine name
M552 S1 ; Enable network
;*** Access point is configured manually via M587
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet
M575 P1 S1 B57600 ; Panel Due

; Printer geometry
M669 K1 ; Select CoreXY mode
M208 X0:330 Y0:285.75 Z0:350 ; Axis Limits
M564 H0 ; allow unhomed movement

;------- drives from top---------------------------------------------------
; B -------+------ A
; | P.02 | P.03 |
; -------+------- Z-Drives
; | P0.1 | P0.4 |
; -------+-------
; Front

; Drive Mappings
M569 P0.0 S1 V0 ; Drive 0: E Axis
M569 P0.1 S1 V0 ; Drive 1: Z-LeftFront Axis
M569 P0.2 S0 V0 ; Drive 2: Z-LeftRear Axis
M569 P0.3 S1 V0 ; Drive 3: Z-RightRear Axis
M569 P0.4 S0 V0 ; Drive 4: Z-RightFront Axis
M569 P1.0 S1 V0 ; Drive 5: Expansion: B motor (X-axis)
M569 P1.1 S1 V0 ; Drive 6: Expansion: A motor (Y-axis)

; Motor remapping for dual Z and axis Limits
M584 X1.0 Y1.1 Z0.1:0.2:0.3:0.4 E0.0 ; Motor mapping
M671 X-76.2:-76.2:406.4:406.4 Y0:374.65:374.65:0 S20 ; Z leadscrews positions Left Front - Let Rear - Right Rear - Right Front

; Microstepping and Speed
M350 X32 Y32 E16 Z16 I1 ; Configure microstepping with interpolation
M92 X200.00 Y200.00 Z200.00 E400.00 ; Set steps per mm 1.8 motors

; Speeds, Acceleration and Jerk
M566 X400.00 Y400.00 Z25.00 E600.00 P1 ; Set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00 Z1000.00 E3600.00 ; Set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z100.00 E3600.00 ; Set accelerations (mm/s^2)

; Motor currents
M906 X1200.00 Y1200.00 Z1200.00 E700.00 I60 ; Set motor currents (mA) and motor idle factor in percent
M84 S600 ; Set idle timeout

; Endstops for each Axis
M574 X2 S1 P"io0.in" ; Set X endstop controlled by switch
M574 Y2 S1 P"io1.in" ; Set Y endstop controlled by switch

; Z-Probe
M558 P8 C"io3.in" H5 F120 T60000 ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X15:215 Y15:195 S20 ; define mesh grid

; Stallgaurd Sensitivy (maybe use to pause print after crash)
M915 X S2 F0 H200 R0 ; Set X axis Sensitivity 1.8 motors
M915 Y S2 F0 H200 R0 ; Set y axis Sensitivity 1.8 motors

; Input Shaper and Accelerometer
;M955 P0 C"io4.out+io4.in"
;M593 F46.75 S0.2
;M593 F19 P4 S0.3 ; experimental

; Z Probe Offset (Probe behind Afterburner)
G31 P500 X0 Y0 Z1.5

; Heaters
M308 S0 P"temp_0" Y"thermistor" A"Bed" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out_0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 A350 C139 D5.5 B0 ; set model parameters for heater 1 and use PID mode
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C

M308 S1 P"temp_1" Y"thermistor" A"Hotend" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out_1" T1 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 R1.680 C233.0:193.0 D6.75 S1.00 V23.7 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"out7" Q500 ; Parts cooling create fan 0 on pin out7 and set its frequency
M106 P0 T45 H0

M950 F1 C"out8" Q500 ; Extruder create fan 1 on pin out8 and set its frequency
M106 P1 T25 H1

; Fans Electronic compartment & Exhaust
;M950 F1 C"out3" Q100 ; Creates Case Fan 1
;M106 P1 T40 S150 H0 ; Case Fan 1 Settings (Turns on at 60°C tool temp) at low speed
;M950 F2 C"out4" Q100 ; Creates Case Fan 2
;M106 P2 T40 S150 H0 ; Case Fan 2 Settings (Turns on at 60°C tool temp) at low speed
;M950 F5 C"out7" Q100 ; Creates Case Fan 2
;M106 P5 T95 S50 H0 ; Exhaust fan

; Filament Runout sensor
;M950 J4 C"io5.in" ; Input 4 filament sensor
;M581 P4 T2 S1 R1 ; Filament Sensor P4 triggers inactive-to-active edge (S1) tigger2.g (T2) only when printing (R1)
;M591 D0 P1 C"io5.in" S1 ; Filament Sensor

; Tools
M563 P0 D0 H1 F0 S"Extruder" ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

This is where its at right now

[alankilian]

@frnknstn

Do you have your fans hidden in the "Status" tab?

[Gixxerfast]

@frnknstn said in seeing if i can get assistance with bed connectins:

M106 P0 T45 H0

This one: M106 P0 T45 H0 ---> M106 P0 S0 H-1 right? You don't want the part cooling fan with thermostatic control. You want the Slicer to handle that one

[frnknstn]

@alankilian 

I dont see anything

[alankilian]

This post is deleted!

[frnknstn]

@alankilian right, that dont do anything if turned all the way up

[Gixxerfast]

@frnknstn Did you fix this?

"This one: M106 P0 T45 H0 ---> M106 P0 S0 H-1 right? You don't want the part cooling fan with thermostatic control. You want the Slicer to handle that one"

[frnknstn]

I changed the comment now i get fan 0 at the bottom. but i still have no action

[Gixxerfast]

@frnknstn OK, that's one. Now we must check your tool config ...

and later your wiring...

[frnknstn]

@gixxerfast glad you guys are helping. new to this and trying to learn. appreciate your patients

[alankilian]

@frnknstn said in seeing if i can get assistance with bed connectins:

@gixxerfast glad you guys are helping. new to this and trying to learn. appreciate your patients

You're doing GREAT!

We've all been where you are right now.

[Gixxerfast]

@frnknstn
Now replace

M563 P0 D0 H1 F0 S"Extruder" ; Define tool 0

with

M563 P0 D0 H1

Just to test and reset the board

Add a T0 at the very end of config.g as well

Shouldn't make much difference but ...

[frnknstn]

@gixxerfast it is changed

[Gixxerfast]

@frnknstn

Same, no TOOL FAN ?

Can you paste your config.g again within the < />

[frnknstn]

@frnknstn

it put Tool fan under fans. No movement yet though

[Gixxerfast]

@frnknstn Oh, yes. #2 done. Now try to max that one and see if any fan spins.

Drag it to max