Z homing issu whit endstop please help

bartekp

@bartekp I try to change Z1 to Z2 or S1 to 0 or 2 and the sama results

bartekp

@jay_s_uk I changed the home z and nothing changed

jay_s_uk

@bartekp it should change the direction it homes in when using just G28 Z or Home z on the DWC screen.
Otherwise ditch the endstop and move the head to the middle of the bed and probe using G30

bartekp

@jay_s_uk G28 table go up but whit G28 Z table goes down and when I pusch Z endstops the table stops

bartekp

@jay_s_uk im not sure if my Z probe is good code in config g

jay_s_uk

@bartekp sounds like your z motor need inverting then. As Z0 should be when the bed is in its highest position. Change the S value on the M569 line in your config to either S1 or S0.
Then reboot and home x, y and z independently and see if it's in the right position. DWC should show 0 for z once homed

bartekp

@jay_s_uk OK I inverted the Z motors works bether!
What I meand that when I pusch X home or Y home table move down and home this axis and back to position , and after this i must homing Z what work also perfect
but If i Puch home all axis table go down and down and down and I must restatr the maschine

jay_s_uk

@bartekp edit the home z portion of homeall to match the same as in homez.
If you're not sure, post your homeall here and I'll edit it for you

bartekp

@jay_s_uk ; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.3 on Mon Oct 04 2021 22:39:47 GMT+0200 (czas środkowoeuropejski letni)
G91 ; relative positioning
G1 H2 Z5 F12000 ; lift Z relative to current position
G1 H1 X-505 Y-505 F1800 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-505 ; home X axis
G1 H1 Y-505 ; home Y axis
G1 X5 Y5 F12000 ; go back a few mm
G1 H1 X-505 F360 ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-505 ; then move slowly to Y axis endstop
G1 H1 Z605 F360 ; move Z up stopping at the endstop
G90 ; absolute positioning
G92 Z600 ; set Z position to axis maximum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F200 ; lift Z relative to current position
;G90 ; absolute positioning

bartekp

@bartekp ; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.3 on Mon Oct 04 2021 22:39:47 GMT+0200 (czas środkowoeuropejski letni)
G91 ; relative positioning
G1 H2 Z5 F12000 ; lift Z relative to current position
G1 H1 X-505 Y-505 F1800 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-505 ; home X axis
G1 H1 Y-505 ; home Y axis
G1 X5 Y5 F12000 ; go back a few mm
G1 H1 X-505 F360 ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-505 ; then move slowly to Y axis endstop
G1 H1 Z605 F360 ; move Z up stopping at the endstop
G90 ; absolute positioning
G92 Z600 ; set Z position to axis maximum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F200 ; lift Z relative to current position
;G90 ; absolute positioning

jay_s_uk

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.3 on Mon Oct 04 2021 22:39:47 GMT+0200 (czas środkowoeuropejski letni)
G91 ; relative positioning
G1 H2 Z5 F12000 ; lift Z relative to current position
G1 H1 X-505 Y-505 F1800 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-505 ; home X axis
G1 H1 Y-505 ; home Y axis
G1 X5 Y5 F12000 ; go back a few mm
G1 H1 X-505 F360 ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-505 ; then move slowly to Y axis endstop
G1 H1 Z-605 F360 ; move Z up stopping at the endstop
G90 ; absolute positioning
;G92 Z600 ; set Z position to axis maximum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F200 ; lift Z relative to current position
;G90 ; absolute positioning

There you go

bartekp

@jay_s_uk HI You mean G92 adjust for z 100 like this ??

bartekp

@bartekp said in Z homing issu whit endstop please help:

@jay_s_uk HI You mean G92 adjust for z 100 like this ??

Can you look at Z probe if is good generated ?

; Z-Probe
M558 P5 C"^zprobe.in" H5 F120 T12000 ; set Z probe type to switch and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X70:500 Y70:500 S20 ; define mesh grid

jay_s_uk

@bartekp said in Z homing issu whit endstop please help:

@jay_s_uk HI You mean G92 adjust for z 100 like this ??

i'm not sure what you mean here

@bartekp said in Z homing issu whit endstop please help:

@bartekp said in Z homing issu whit endstop please help:

@jay_s_uk HI You mean G92 adjust for z 100 like this ??

Can you look at Z probe if is good generated ?

; Z-Probe
M558 P5 C"^zprobe.in" H5 F120 T12000 ; set Z probe type to switch and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X70:500 Y70:500 S20 ; define mesh grid

what type of probe is it?
you can check the status of the probe on this window

If its red, its triggered, if its not red, its not

bartekp

@jay_s_uk Bltouch sorry for that

jay_s_uk

@bartekp no as you appear to be missing the servo configuration https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_Software_setup_RepRapFirmware_Num_3
What board are you using and where is the bltouch connected?
You should also have deployprobe.g and retractprobe.g in your sys folder

bartekp

@jay_s_uk https://d17kynu4zpq5hy.cloudfront.net/igi/duet3d/KUDxTZSs3rnd3JVH.full

bartekp

@bartekp deployprobe.g and retractprobe.g duet 2 wifi

jay_s_uk

@bartekp then you should have this line in your config
M950 S0 C"exp.heater3"
if you add that, does the probe react to M401 and M402?
What's the contents of those deploy and retract files?

bartekp

@jay_s_uk sory i forgot i dont have this files I working on reach them please wait