Update CR-10+Duet wifi from 2.05.1 to 3.0 firmware
-
if you made no changed to your config after the config tool, you can upload the json
or read
https://duet3d.dozuki.com/Wiki/RepRapFirmware_3_overview#Section_Summary_of_what_you_need_to_do_to_convert_your_configuration_and_other_files
and make the changes by hand -
@Veti ok... its decided... i ll make by hand. My first doubt is:
what kind of termistor do i have? I know is a 24V hotend heater and my bed is heated with a silicon heater of 240W connected to KS 1-25DA rele. I dont undestand about the values i have to imput on the config.g! Can you help me on this? Sorry
-
@Hélder-Rocha said in Update CR-10+Duet wifi from 2.05.1 to 3.0 firmware:
I know is a 24V hotend heater and my bed is heated with a silicon heater of 240W connected to KS 1-25DA rele
best to ask the seller.
most of the time those are B3950 -
@Veti is that for the hotend heater or for the bed?
-
the bed.
on the hotend it is probably easier to just buy a know thermistors.
-
@Veti i ll try to check it out... tks
-
so i have this on the new rules:
M143
In RRF 2 the optional P parameter of the M143 command is the number of the global heater protection element instance, and it defaults to the heater number (H parameter). Valid values are 0..(MaxHeaters-1) and 100..(MaxHeaters-1). The optional X parameter is the number of a heater or virtual heater whose sensor is used to monitor the heater.
In RRF 3.01-RC2 and later the optional P parameter is the number of the monitor for that particular heater. Valid values are 0..2 and the default is 0. The optional T parameter is the number of the sensor used to monitor the heater.
In my config.g i have the M143 for the bed like this:
M143 H0 S120and for the hotend heater:
M143 H1 S290What should i change?
-
what i do in that case, is generate a config in the online configurator and have a look at that layout
-
@Veti ok...i ll keep it for now
-
Veti, i find out i have a "G10" on tools, setting the axis offsets to 0. Could that be the problem when i was trying to define a different offset on G31 when i was calibrating my BLTouch?
On TOOLS i have this:G10 P0 X0 Y0 Z0
-
no the first tool should not have an offset
-
@Veti so... i should erase it?
-
no. compare to the config that the configuration generates. its there.
-
@Veti i a making the changes directly in the config.g
-
note what i wrote above
what i do in that case, is generate a config in the online configurator and have a look at that layout
-
@Veti yes, i know... your right but, i dont understand nothing about what the online configuration RRF asks! For instance... i am looking at it and in the heaters, in the bed, what is going to be the output? Bedheat= Inverted? e0heat?... i dont know what that means and a lot of other things in it!! Thats why i have to copy from what other people do....sorry Veti, but this is not my area of expertise, just want to have a nice and good printer working!
-
invert means swap the signal. so if for some reason your heater would be heating if its off, you invert the signal. unlikely that you will need it for the heaters.
-
@Veti allright... sinse i have a CR-10, but with a lot of upgrades in it, in the web configuration tool, i selected the ender 3, because is from creality also. I beleave a lot of things ara alike.
Ok... in the first board i change the name of the rinter, change the neasurs of the bed and the height of the printes. About the homing preferences, i didnt touched. 2º board:Drives:
Xstop;
Ystop
Zstop.Heaters:
Bed-bedheat-bedtemp
Nozzle-e0heat-e0tempZprobe (i have a bltouch):
Zprobe.in
Zprobe.mod
exp.heater7 (not sure about this one)fan mapping:
fan0
fan1
fan2could it be ok? I dont know about the bed, because i have a silicone heater that is powered with 230V and is controled by a rele.
-
looks ok.
the bltouch port depends on the port where you connected it
-
@Veti said in Update CR-10+Duet wifi from 2.05.1 to 3.0 firmware:
looks ok.
the bltouch port depends on the port where you connected it
Yes... i have it on the 4th pin near the red and the broun. I beleave is nº7
