Z offset is .030 too high after starting print?
-
No offset configured in cura.
I can use the baby stepping to fix it but I have to click it a ton of times... I've just been manually turning the z motor to adjust the offset.Here is the GCODE:
;FLAVOR:Marlin ;TIME:10883 ;Filament used: 5.77495m ;Layer height: 0.1 ;MINX:117.122 ;MINY:126.967 ;MINZ:0.3 ;MAXX:183.437 ;MAXY:171.213 ;MAXZ:74.4 ;Generated with Cura_SteamEngine 4.4.0 M140 S60 M105 M190 S60 M104 S225 M105 M109 S225 M82 ;absolute extrusion mode G1 Z5 F15000 ;Move the platform down 5mm G28 ;Home ;Prime the extruder G92 E0 G1 F200 E3 G92 E0 G92 E0 G92 E0 G1 F1500 E-6.5 ;LAYER_COUNT:742 ;LAYER:0 M107 G0 F2215.4 X118.845 Y138.206 Z0.3 ;TYPE:SKIRT G1 F1500 E0 G1 F1200 X119.46 Y137.693 E0.03996 G1 X119.512 Y137.65 E0.04332 G1 X120.337 Y136.988 E0.09609 G1 X121.752 Y135.797 E0.18837 G1 X122.38 Y135.373 E0.22617 G1 X122.98 Y135.054 E0.26007 G1 X123.046 Y135.02 E0.26378 G1 X124.288 Y134.392 E0.33321 G1 X126.703 Y133.084 E0.47023 G1 X129.059 Y131.72 E0.60605 G1 X130.064 Y131.104 E0.66486 G1 X130.114 Y131.074 E0.66777 G1 X130.708 Y130.723 E0.70219 G1 X130.795 Y130.673 E0.7072 G1 X131.073 Y130.519 E0.72305 G1 X131.446 Y130.339 E0.74372 G1 X131.917 Y130.145 E0.76913 G1 X132.007 Y130.11 E0.77395 G1 X132.443 Y129.944 E0.79722 G1 X132.726 Y129.849 E0.81212
-
Can you try updating to the latest 2.05 firmware release?
-
I did that yesterday actually, no change
-
@TheBasedDoge said in Z offset is .030 too high after starting print?:
G0 F2215.4 X118.845 Y138.206 Z0.3
are you sure the web gui is report 0.03 and not 0.3 ?
-
Yes ^
Ok, so I tried PrusaSlic3r and it's not doing it? Where in Cura would be causing this weird issue?
-
Can you save a .3mf file from cura and post it somewhere to share it here?
-
sure, try this
https://www.dropbox.com/s/wnt6123go95dghe/test.3mf?dl=0 -
That .3mf doesn't seem to open at all in Cura.
-
Huh that's weird.
Try this one: https://www.dropbox.com/s/enx9kfmvuy7e1vu/CFFFP_test.3mf?dl=0I just tested and it opened on my cura 4.4.1
-
That one worked.
I still don't see anything that would add an additional 0.03 offset.