XYZ carriage rise without reason
-
@fcwilt said in XYZ carriage rise without reason:
Hi,
Did you verify that the cables to the extruder motors are good?
Frederick
The motor and cable works well because I tried to connect it to x driver.
-
@MrOppip said in XYZ carriage rise without reason:
@fcwilt said in XYZ carriage rise without reason:
Hi,
Did you verify that the cables to the extruder motors are good?
Frederick
The motor and cable works well because I tried to connect it to x driver.
I read that you tried the X,Y motors with the E0,E1 drivers. I missed where you tried the extruder motor with the X driver.
When trying to extrude via DWC do you have a tool selected?
Frederick
-
@fcwilt said in XYZ carriage rise without reason:
@MrOppip said in XYZ carriage rise without reason:
@fcwilt said in XYZ carriage rise without reason:
Hi,
Did you verify that the cables to the extruder motors are good?
Frederick
The motor and cable works well because I tried to connect it to x driver.
I read that you tried the X,Y motors with the E0,E1 drivers. I missed where you tried the extruder motor with the X driver.
When trying to extrude via DWC do you have a tool selected?
Frederick
it was written in the previous post
sure, otherwise the extrusion and protrusion button is disabled
-
can you tell us step by step how you are trying to extrude? every button you press, every command you issue.
-
@Veti said in XYZ carriage rise without reason:
can you tell us step by step how you are trying to extrude? every button you press, every command you issue.
first method:
power on duet
home all
activated heater
heated 200 °
in "extruder control" pressed extrude
then retract.second method:
power on duet
activated heater
in "gcode console" given command M302 P1
then G1 E50
then G1 E-50nothing moves
-
can you verify with a multimeter that the phases on the extruder stepper are correct.
i.e. one phase for red and blue and one for green and black. -
-
@fcwilt
activated the heater means the same as selected the tool.@Veti
yes is the first thing I checked to run it correctly.
I found that my hardware is perfect because I loaded the Creality Ender 3 Pro predefined configuration from the RepRapFirmware Configuration Tool and the extruder works.so there's something in myFW that doesn't make the extruder go.
I have the BLTouch, connected to the heater 3 (disabled as in the tutorials).
does it interfere in any way?in the meantime, thanks for the support
-
@MrOppip said in XYZ carriage rise without reason:
@fcwilt
activated the heater means the same as selected the tool.Hmm...
I cannot check right now but I'm pretty sure a tool can have it's heater in the standby state without the tool being active.
Frederick
-
@MrOppip said in XYZ carriage rise without reason:
I have the BLTouch, connected to the heater 3 (disabled as in the tutorials).
does it interfere in any way?its shouldnt, but its an easy check. comment the line and try it.
do you have a config-overwrite? because you have a M501 in your config.
please post the config where it was working.
-
@Veti said in XYZ carriage rise without reason:
do you have a config-overwrite? because you have a M501 in your config.
I'm not sure if it's useful. I had enabled it along with the ability to save the print in the event of a blackout.
please post the config where it was working.
checking it I saw that:
; Tools
M563 P0 D0 H1 F0in my CR10 file config D0 is not there.
I don't know why the online configurator doesn't create it.
can it be the cause? I haven't had time to try yet.
-
yes
If there is no 'D' field the tool has no drives. -
@Veti said in XYZ carriage rise without reason:
yes
If there is no 'D' field the tool has no drives.ok! sorry for the delay but I checked only now.
the problem was just that "D" missing.
now everything works as it should.Thanks for your help.
