Heater 1 isn't showing

tenlogtak

I edited my config file to change tool offsets since I've changed extruders. After resetting Heater 1 no longer shows up. I tried reverting to a saved config file and it didn't help.

Duet2 Wifi, Duex5, Tenlog TL-D3 printer, RepRapFirmware for Duet 2 WiFi/Ethernet 3.3 (2021-06-15)
Duet WiFi Server Version: 1.26

Here's my config file.

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
;

; General preferences
G21 						; Work in millimetres
G90 						; Send absolute coordinates...
M83 						; ...but relative extruder moves

; Network
M550 D3 Duet        ; Set machine name
M552 S1                       ; Enable network
M586 P0 S1                                      ; Enable HTTP
M586 P1 S0                                      ; Disable FTP https://duet3d.dozuki.com/Wiki/Gcode#Section_M505_Set_configuration_file_folder
M586 P2 S0                                      ; Disable Telnet

; Drives direction
M569 P0 S1 					; Physical drive 0 goes forward (X1)
M569 P1 S1 					; Physical drive 1 goes forwards (Y)
M569 P2 S1 					; Physical drive 2 goes forwards (Z1)
M569 P3 S1 					; Physical drive 3 goes forwards (X2 on e0)
M569 P4 S0 					; Physical drive 4 goes backwards (Z2)
M569 P5 S0 					; E0 - Physical drive 5 goes backwards 
M569 P6 S1 					; E1 - Physical drive 6 goes forwards 

; Drive mapping
M584 X0 Y1 Z2:4 U3 V4 E5:6 P4			; Drive mapping X=0, Y=1, Z=2 and 4, X2=U=3 and Z2=V=4, extruder motors 5 and 6. Drive 2 and 4 is combined Z. 4 axes are visible				

; Endstops
M574 X1 S1 P"!xstop"                                             ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"!ystop"                                             ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"!zstop"                                             ; configure active-high endstop for low end on Z via pin zstop
M574 U2 S1 P"!e0stop"
M574 V1 S1 P"!e1stop"

M671 X-20:325 Y0:0 S0.5 			; leadscrews at left and right of X axis

;Microstepping
M350 X64 Y64 Z64 U64 V64 I1  	        ; Configure microstepping with interpolation
M350 E32:32 I0  	        	; Configure microstepping with interpolation

; Stepps per millimeter
M92 X326.4 Y326.4 Z3200 U326.4 V3200	; Set steps per mm
M92 E184:184					; stock D3 extruder value 92, that is double, so 184 at 32 microstepping, rbmg

; Movement and speed parameters			
M566 X450 Y450 Z120 U450 V120			; Set maximum MOVEMENT instantaneous speed changes (mm/min) 
M566 E150:150							; Set maximum EXTRUDERS instantaneous speed changes (mm/min)

M203 X9000 Y9000 Z800 U9000 V800		; Set maximum MOVEMENT speeds (mm/min)
M203 E3600:3600					; Set maximum EXTRUDERS speeds (mm/min)
M201 X1000 Y1000 Z800 U1000 V800		; Set MOVEMENT accelerations (mm/s^2)
M201 E5000:5000				; Set EXTRUDERS accelerations (mm/s^2)
M906 X1100 Y1300 Z980 U1100 V980 I30		; Set MOVEMENT motor currents (mA) and motor idle factor in per cent
M906 E1200:1200 I30				; Set EXTRUDER motor currents (mA) and motor idle factor in per cent, stock value 1197

; Axis Limits 0,0 origin at bed center
M208 X-192 Y-155 Z0 U-150 V0 S1             ; Set axis minima
M208 X150 Y155 Z360 U194 V360 S0              ; Set axis maxima

; Filament runout sensors -  enable and connect to E- motor enstops
M591 D5 P2 C10 S0			        ; Filament monitoring for printhead 1 on endstop 10
M591 D6 P2 C11 S0			        ; Filament monitoribg for printhead 2 on endstop 11


M557 X-100:150 Y-120:140 S20 ; probe from X Y= with a mesh spacing of 20mm

; Z-Probe
M950 S0 C"duex.pwm1" ; Duet 2 WiFi/Ethernet
M558 P9 C"^zprobe.in" H5 F120 T6000
G31 X20 Y0 Z6.666 P25



M307 H6 A-1 C-1 D-1 ; Disable the 7th Heater to free up PWM channel 5 on the Duex board.
M950 S7 C"duex.e6heat"  ; assign GPIO port 0 to heater6 on expansion connector, servo mode

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138                  ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                                           ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00                                                ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                                         ; map heated bed to heater 0
M143 H0 S120                                                    ; set temperature limit for heater 0 to 120C


M308 S1 P"duex.e2temp" Y"thermistor" T100000 B4138              ; configure sensor 1 as thermistor on pin duex.e2temp
M950 H1 C"duex.e2heat" T2                                       ; create nozzle heater output on duex.e2heat and map it to sensor 1
M307 H1 B0 S1.00                                                ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                                    ; set temperature limit for heater 1 to 280C


M308 S2 P"duex.e3temp" Y"thermistor" T100000 B4138              ; configure sensor 2 as thermistor on pin duex.e3temp
M950 H2 C"duex.e4heat" T2                                       ; create nozzle heater output on duex.e4heat and map it to sensor 2
M307 H2 B0 S1.00                                                ; disable bang-bang mode for heater  and set PWM limit
M143 H2 S280                                                    ; set temperature limit for heater 2 to 280C

; Fans
M950 F0 C"duex.fan6" Q250                                         ; create fan 0 on pin duex.fan6 and set its frequency
M106 P0 S255 H-1                                                  ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"duex.fan7" Q250                                           ; create fan 1 on pin duex.fan7 and set its frequency
M106 P1 S255 H-1                                                  ; set fan 1 value. Thermostatic control is turned off
M950 F2 C"duex.fan3" Q250                                       ; create fan 2 on pin duex.fan3 and set its frequency
M106 P2 S255 H-1                                                  ; set fan 2 value. Thermostatic control is turned off
M950 F3 C"duex.fan4"  Q250                                     ; create fan 3 on pin duex.fan4 and set its frequency
M106 P3 S255 H-1                                                  ; set fan 3 value. Thermostatic control is turned off

	; TOOLS
;Left printhead - T0
M563 P0 D0 H1 F0 				; Tool 0 uses Motor 5 for extruder, heater 3 and fan 0
G10 P0 X0 Y26 Z0				; Set tool 0 axis offsets
G10 P0 R0 S0 					; Set initial tool 0 active and standby temperatures to 0C

; Right printhead - T1
M563 P1 D1 H2 X3 F2 				; Tool 1 uses Motor 6 for extruder, heater 4 and fan , ports X axis movement to drive 3
G10 P1 Y-19.2 U-2 Z0		; Set tool 1 axis offsets
G10 P1 R0 S0 				; Set initial tool 1 active and standby temperatures to 0C

; DUPLICATION TOOL - T2  
;Use "M579 U-1" in start slicers start script for mirror mode
; G10 P2 X-50 Y0 U50 S0 R0    			; Set tool offsets and temperatures for tool 2 - moves X 75 left and U 75 right
; M563 P2 D0:1 H1:2 X0:3 F3:4			; Tool 2 uses both extruders and hotend heaters, maps X to both X and U, and uses both print cooling fans 3 and 4
; M567 P2 E1.00:1.00 				; Set mix ratio 100% on both extruders
; M568 P2 S1 					; Turn on mixing for tool 2

; Automatic saving after power loss is enabled
M911 S22 R23 P"M913 X0 Y0 U0 G91 M83 G1 Z3 E-5 F1000" 	; Set voltage thresholds and actions to run on power loss

; Custom settings are configured in config-override.g
M501

tenlogtak

Yay! I sorted it out.

I went back to an older config file I had saved and just started changing blocks of code one at a time until i figured out what was messing up.

I guess I hadn't paid attention after getting the bed probe set up. I had the bed probe on pins shared by the heater. Its all working, for now.