Connecting Duet Wifi to slicer software

TimVukman

Unclogged. I can manually push on the filament and it will flow out of the nozzle. I've played with the feedrate and amount settings and it doesn't seem to want to push it through.

If I manually get it started, it will feed for a bit, and then it will stop and the stepper just rocks back and forth, seemingly between forward and backward. Any chance it need more current to turn the motor against the backpressure of feeding the filament out of the nozzle?
Thanks
Tim

number40fan

Could be. A sent you an email, btw.

TimVukman

Ok, after your post of 20:12

Current M92 in config.g :
X640 Y640 Z3200 E400

Changed to
M92 X80 Y80 Z1600 E822

Commented two lines that set Z probe since I don't have mine yet.
Rmoved M92 line from script file

Edited last line in Config.g to change tool to T0 since I only have 1 extruder.
Moved T0 to M104 line in script file:

Thanks
Tim

Script:
M104 T0
G28 ; home all
G92 E0
G1 Z0.1 F1000
G1 X8.0 F2000
G1 Y60.0 E4.0 F1000.0 ; prime
G1 Y100.0 E8.5 F1000.0 ; prime
G92 E0

Config.g
; Configuration file for Duet WiFi (firmware version 1.17)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Fri Sep 08 2017 10:03:01 GMT-0400 (Eastern Daylight Time)

; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates…
;M83 ; ...but relative extruder moves
M555 P2 ; Set firmware compatibility to look like Marlin
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X210 Y280 Z180 S0 ; Set axis maxima

; Endstops
M574 X1 Y1 Z1 S0 ; Define active low and unused microswitches
;M558 P0 X0 Y0 Z0 H5 F120 T6000 ; Set Z probe type to switch, the axes for which it is used and the probe + travel speeds
;G31 P600 X0 Y0 Z2.5 ; Set Z probe trigger value, offset and trigger height
M557 X25:175 Y25:175 S20 ; Define mesh grid

; Drives
M569 P0 S0 ; Drive 0 goes backwards
M569 P1 S0 ; Drive 1 goes backwards
M569 P2 S0 ; Drive 2 goes backwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X128 Y128 Z128 E16 I0 ; Configure microstepping without interpolation
M92 X80 Y80 Z1600 E822 ; Set steps per mm
M566 X900 Y900 Z12 E120 ; Set maximum instantaneous speed changes (mm/min)
M203 X12000 Y12000 Z1200 E3000 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z100 E5000 ; Set accelerations (mm/s^2)
M906 X855 Y855 Z855 E855 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Heaters
M143 S260 ; Set maximum heater temperature to 260C
M305 P0 T100000 B3988 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M305 P1 T100000 B4725 C0 R4700 ; Set thermistor + ADC parameters for heater 1

; Tools
M563 P1 D0 H1 ; Define tool 1
G10 P1 X0 Y0 Z0 ; Set tool 1 axis offsets
G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C

; Network
M550 PTevo Tarantula ; Set machine name
M552 S1 ; Enable network
; Access point is configured manually via M587 by the user
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 S1 I0 F500 H-1 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off

; Custom settings are not configured

; Miscellaneous
T0 ; Select first tool

number40fan

How many amps do your motors use? Should be a sticker on them.

TimVukman

Woah

I think it might be doing something, but it is really hard to tell. It took forever to make the effort to home all and it did that very slowly and so far it has not moved off of home.

I had forgotten the other change to M92. for the extruder settings so I have done that and reset.

I am still getting "attempting to extrude with no tool selected" and the extruder is not feeding.

TimVukman

After the last reset, the speed is ok, but still "attempting to extrude with no tool selected."

number40fan

Under tools. M563 P0 instead of P1.

number40fan

The G10's under it, change to P0 as well.

number40fan

https://duet3d.com/wiki/Tuning_the_heater_temperature_control

Make sure you do these steps too.

TimVukman

The sticker says Tevo 17HD4401-c5.18

Google was no help on that number. I found a posting on their facebook owner page where someone got a spec sheet. Theirs is 1.5A, and Tevo says 1.4 to 1.7 is ok to use.

Tim

number40fan

Once you get everything squared away, you can up the numbers in M906 X855 Y855 Z855 to 1200 or so and even E up to a 1000 or so.

TimVukman

Hi number40fan

TeamViewer is installed. Let me know what you need and I will send it via private email to the one you sent me the email from

Thanks,
Tim

number40fan

Emailed you back.