Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    problem Set Mesh Parameters

    Scheduled Pinned Locked Moved
    Config Tool
    2
    8
    298
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • konte1978undefined
      konte1978
      last edited by

      hello guys I have a problem that I can't solve by myself, I can't define the space to probe related to the bltouch.
      If I vary the minimum and maximum values x y of the command M557 X24: 290 Y76: 295 S20 I do not get any variation it always starts at the same point above the glass clip.

      Vetiundefined 1 Reply Last reply Reply Quote 0
      • Vetiundefined
        Veti @konte1978
        last edited by

        @konte1978 said in problem Set Mesh Parameters:

        M557 X24: 290 Y76: 295 S20

        there should be no space after the :

        konte1978undefined 1 Reply Last reply Reply Quote 0
        • konte1978undefined
          konte1978
          last edited by

          I am attaching my config.g
          ; Configuration file for Duet WiFi (firmware version 3)
          ; executed by the firmware on start-up
          ;
          ; generated by RepRapFirmware Configuration Tool v3.1.4 on Fri Jul 17 2020 20:24:58 GMT+0200 (CEST)

          ; General preferences
          G90 ; send absolute coordinates...
          M83 ; ...but relative extruder moves
          M550 P" CUBE PRO TRIO" ; set printer name

          ; Network
          M552 S1 ; enable network
          M586 P0 S1 ; enable HTTP
          M586 P1 S0 ; disable FTP
          M586 P2 S0 ; disable Telnet

          ; Drives
          M569 P0 S1 ; physical drive 0 goes forwards
          M569 P1 S1 ; physical drive 1 goes forwards
          M569 P2 S1 ; physical drive 2 goes forwards
          M569 P3 S1 ; physical drive 3 goes forwards
          M569 P4 S1 ; physical drive 4 goes forwards
          M569 P9 S1 ; physical drive 9 goes forwards
          M584 X0 Y1 Z2 E3:4:9 ; set drive mapping
          M350 X16 Y16 Z16 E16:16:16 I1 ; configure microstepping with interpolation
          M92 X87.35 Y87.43 Z1076.77 E82.09:82.09:82.09 ; set steps per mm
          M566 X900.00 Y900.00 Z12.00 E120.00:120.00:120.00 ; set maximum instantaneous speed changes (mm/min)
          M203 X15000.00 Y15000.00 Z1200.00 E600.00:600.00:600.00 ; set maximum speeds (mm/min)
          M201 X500.00 Y500.00 Z250.00 E250.00:250.00:250.00 ; set accelerations (mm/s^2)
          M906 X1500 Y1500 Z800 E1200:1200:1200 I30 ; set motor currents (mA) and motor idle factor in per cent (ho modficato la corrente dei motori dell'estrusore da 800 a 1200)
          M84 S30 ; Set idle timeout

          ; Axis Limits
          M208 X0 Y0 Z0 S1 ; Imposta valore minimo deli assi
          M208 X290 Y295.3 Z205 ; imposta il valore massimo degli assi ho tolto il valore S0 ALLA FINE DELLA RIGA

          ; Endstops
          M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
          M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
          M574 Z1 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop

          ; Z-Probe
          M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
          M950 S0 C"duex.pwm5" ; creare il servo pin 0 per BLTouch
          M558 P9 C"^zprobe.in" H5 F120 T6000 A10 R0.75 S0.02 ; set Z probe type to bltouch and the dive height + speeds
          G31 P25 X82 Y-50.5 Z2.75 ; impostare il valore del trigger della sonda Z, l'offset e l'altezza del trigger
          M557 X24:290 Y76:295 S20 ; define mesh grid

          ; Heaters
          ;Piatto riscaldato
          M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
          M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
          M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
          M140 H0 ; map heated bed to heater 0
          M143 H0 S110 ; set temperature limit for heater 0 to 120C
          ;Estrusore numero 1
          M308 S1 P"spi.cs1" Y"rtd-max31865" ; configure sensor 1 as thermistor on pin e0temp
          M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
          M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
          M143 H1 S290; set temperature limit for heater 0 to 120C
          ;Estrusore numero 2
          M308 S2 P"spi.cs2" Y"rtd-max31865" ; configure sensor 2 as thermistor on pin e1temp
          M950 H2 C"e1heat" T2 ; create nozzle heater output on e1heat and map it to sensor 2
          M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
          M143 H2 S270
          ;Estrusore numero 3
          M308 S3 P"spi.cs3" Y"rtd-max31865" ;M308 S3 P"duex.e2temp" Y"thermistor" T100000 B4725 ; configure sensor 3 as thermistor on pin duex.e2temp
          M950 H3 C"duex.e2heat" T3 ; create nozzle heater output on duex.e2heat and map it to sensor 3
          M143 H3 S270 ; set temperature limit for heater 0 to 120C
          M307 H3 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
          ; Riscaldatore della camera
          M141 H4 ; il riscaldatore 4 è il riscaldatore della camera
          M950 H4 C"duex.e3heat" T4 ; configura l'uscita per il riscaldamento della camera sull pin e della scheda duex
          M308 S4 P"duex.e3temp" Y"thermistor" T100000 B5500 C7.06Ee-8 ; configure sensor 4 as thermistor on pin duex.e2temp
          M143 H4 S70 ; set temperature limit for heater 0 to 120C
          M301 H4 B1 ; utilizzare il controllo bang-bang per il riscaldatore della camera

          ; Fans
          M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
          M106 P0 C"ESTRUSORI" S0 H3:2:1 T120 ; set fan 0 name and value. Thermostatic control is turned on
          M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
          M106 P1 C"NOZZLE" S0 H1:2:3 T45 ; set fan 1 name and value. Thermostatic control is turned on
          M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
          M106 P2 C"LUCI LED" S0 H-1 ; set fan 2 name and value. Thermostatic control is turned off
          M950 F3 C"duex.fan6" Q500 ; create fan 3 on pin duex.fan6 and set its frequency
          M106 P3 C"VENTOLA 6" S0 H-1 ; set fan 3 name and value. Thermostatic control is turned off
          M950 F4 C"duex.fan7" Q500 ; create fan 4 on pin duex.fan7 and set its frequency
          M106 P4 C"VENTOLA 7" S0 H-1 ; set fan 4 name and value. Thermostatic control is turned off

          ; Tools
          M563 P0 S"estrusore 1" D0 H1 F0:1 ; define tool 0
          G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
          G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
          M563 P1 S"estrusore 2" D1 H2 F0:1 ; define tool 1
          G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
          G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C
          M563 P2 S"estrusore 3" D2 H3 F0:1 ; define tool 2
          G10 P2 X0 Y0 Z0 ; set tool 2 axis offsets
          G10 P2 R0 S0 ; set initial tool 2 active and standby temperatures to 0C

          ; Sensori di folamento degli estrusori

          													;se imposto l'ultima S0 disabilita il confronto tra filamento aspetatto e quello realmente estruso,S1 abilita il controllo
													;valori sensibilità filamneto originale R40:120

          M591 D0 P5 C"e0stop" R5:190 E3.0 S0; ho configurato il filamento del primo estrusore sull'uscita e0stop
          M591 D1 P5 C"connlcd.encb" R5:190 E3.0 S1 ; ho configurato il filamento del secondo estrusore sull'uscita stop10(ECN_B)
          M591 D2 P5 C"e1stop" R5:190 E3.0 S1 ; ho configurato il filamento del terzo estrusore sull'uscita e1stop

          ; Custom settings are not defined
          M575 P1 S1 B57600 ;per abilitare lcd paneldue
          M501

          Vetiundefined 1 Reply Last reply Reply Quote 0
          • konte1978undefined
            konte1978 @Veti
            last edited by

            @Veti no space left, you could take a look at my config.g. Where am I doing wrong???

            1 Reply Last reply Reply Quote 0
            • Vetiundefined
              Veti @konte1978
              last edited by

              @konte1978 said in problem Set Mesh Parameters:

              M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed

              delete this line

              M92 X87.35 Y87.43 Z1076.77

              how did you arrive at those numbers, they seem odd.

              G31 P25 X82 Y-50.5 Z2.75 ; impostare il valore del trigger della sonda Z, l'offset e l'altezza del trigger
              M557 X24:290 Y76:295 S20 ; define mesh grid

              you have to take into offset when defining the mesh

              if you want to probe at x24 your nozzle would have to go to - 58 which is not allowed from your minimum.

              so your x probing should start at x82
              for y the maximum here is 244.

              you should be getting warnings in the console when probing the mesh telling you about this.

              1 Reply Last reply Reply Quote 0
              • konte1978undefined
                konte1978
                last edited by

                thank you very much, I think I have solved I changed the values in G31

                Vetiundefined 1 Reply Last reply Reply Quote 0
                • Vetiundefined
                  Veti @konte1978
                  last edited by

                  @konte1978

                  the G31 need to be correct or the mesh bed levelling will not work correctly.

                  konte1978undefined 1 Reply Last reply Reply Quote 0
                  • konte1978undefined
                    konte1978 @Veti
                    last edited by

                    @Veti said in problem Set Mesh Parameters:

                    the G31 need to be correct or the mesh bed levelling will not work correctly.

                    I made a mark on the plate where I positioned myself above with the nozzle n ° 1 and then with the bltouch probe, I made the difference between the values indicated on the DRO

                    1 Reply Last reply Reply Quote 0
                    • First post
                      Last post
                    Unless otherwise noted, all forum content is licensed under CC-BY-SA