RRF 3.01-RC11 Network Hibernating
-
It's probably just my system, & I looked on the release notes, to see if there was anything, but....
I've had this occur on 3 occasions now, and only since updating to RC11, that the printer appears to be fully working, and can run everything from the Panel Due, but the web\network interfaces appear to have gone into a 'hibernation' state where no browser can connect, neither will the Duet respond a ping\telnet etc.
This appears to occur approx. 20 mins following a print, and the only way I can get back to a contactable system is either issue a 'STOP' command, on the Panel Due, or a power cycle.
No changes have been made to the Config files.
M122=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.01-RC11 running on Duet Ethernet 1.02 or later
Board ID: 08DGM-95BNL-MGPSJ-6J1F2-3SD6L-9JZHXUsed output buffers: 3 of 24 (20 max)
=== RTOS ===
Static ram: 28060
Dynamic ram: 93204 of which 44 recycled
Exception stack ram used: 256
Never used ram: 9508
Tasks: NETWORK(ready,176) HEAT(blocked,1228) MAIN(running,1828) IDLE(ready,76)
Owned mutexes:
=== Platform ===
Last reset 00:02:46 ago, cause: software
Last software reset at 2020-05-04 20:32, reason: User, spinning module GCodes, available RAM 9212 bytes (slot 2)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
MCU temperature: min 31.8, current 33.0, max 33.8
Supply voltage: min 24.2, current 24.3, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-05-04 20:35:00
Cache data hit count 305150093
Slowest loop: 146.97ms; fastest: 0.13ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.8ms, write time 44.9ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 233.11ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 2 of 8
Interface state active, link 100Mbps full duplex
=== DueX ===
Read count 0, nan reads/min
