Firmware wishlist and priorities for Duet WiFi and Duet Ethernet

MitchD

Would it be possible to make the Paneldue play a tune when the print finishes? This just makes the whole experience a bit more friendly, especially when we show off the printers at maker faires etc.

Quadcells

19
17
1
2
18

Thanks

dc42

@mitchd said in Firmware wishlist and priorities for Duet WiFi and Duet Ethernet:

Would it be possible to make the Paneldue play a tune when the print finishes? This just makes the whole experience a bit more friendly, especially when we show off the printers at maker faires etc.

I think it should already be possible, using a combination of M300 and G4.

audryhome

@dc42 Implement G29 T1 tag to list the height table, this makes it possible to communicate with Bed Level Visualizer
see https://plugins.octoprint.org/plugins/bedlevelvisualizer/ for info.

All Octoprint users will love this I guess.

Low priority since this exists in the DUET GUI as a workaround.

rhklein

13
Didn't I read somewhere that it is already implemented or was it a wishlist too? (firmware not Deckingmans script)

DADIY

@dc42 This is already possible, I have the following in my end gcode -

;Play beep beep beep to show print ended.
M300 P500 S5000
G4 P400
M300 P500 S5000
G4 P400
M300 P500 S5000
G4 P400
M300 P500 S5000

Phaedrux

@mitchd If you're looking for a little jingle when a print is finished and not just a beep, try this one:

; Play a triumphant tune to celebrate a successful print.
M400			; Clear queue before jingle
G4 S1
M300 P250 S750
G4 P251
M300 P200 S1250
G4 P201
M300 P250 S750
G4 P251
M300 P200 S1250
G4 P201
M300 P250 S2500
G4 P251
M300 P150 S2000
G4 P151
M300 P150 S2500
G4 P151
M300 P350 S3700
G4 P351
M400

jnolan72

That is too cool

@phaedrux said in Firmware wishlist and priorities for Duet WiFi and Duet Ethernet:

; Play a triumphant tune to celebrate a successful print.
M400 ; Clear queue before jingle
G4 S1
M300 P250 S750
G4 P251
M300 P200 S1250
G4 P201
M300 P250 S750
G4 P251
M300 P200 S1250
G4 P201
M300 P250 S2500
G4 P251
M300 P150 S2000
G4 P151
M300 P150 S2500
G4 P151
M300 P350 S3700
G4 P351
M400

Phaedrux

@jnolan72 If you like that one I have another one for printer start up and another for right before the print starts.

I've tried to program more complex tunes but the more commands you send the more likely the system is to miss a tone or stutter. The buffer can only handle so much I guess. Hence having to issue an M400 before and after. This is more noticeable at printer startup than it is say before or after a print.

;
; Startup Tune. Placed at the end of config.g
;
M400
G4 S2
M300 P200 S2000
G4 P201
M300 P200 S2250
G4 P201
M300 P200 S2000
G4 P201
M300 P200 S2855
G4 P201
M300 P200 S2500
G4 P201
M300 P200 S2200
G4 P201
M300 P200 S2500
G4 P201
M300 P200 S2900
G4 P201
M300 P300 S3500
G4 S1
M400

;
; Lucky tune to start print off on the right foot. Placed in slicer start g-code.
;
M300 P200 S1000
G4 P201
M300 P200 S1250
G4 P201
M300 P200 S1100
G4 P201
M300 P200 S2000
G4 P201
M300 P200 S1500
G4 P201
M300 P200 S1000
G4 P201
M300 P200 S1300
G4 P201
M300 P200 S1000
G4 P201
M300 P300 S1500
G4 S1
M400

mgrimes1907

1,4,5,16,17

Coffee

Thanks guys for the beeps and tunes! My old Creatbot beeps and I was missing that on this new build.

Phaedrux

@coffee Last one... Inspired by my Roomba

; Charge.g
;
; Duh nuh nun nah nah naah Charge!
;
M400
G4 S1
M300 P295 S520
G4 P295
M300 P250 S650
G4 P250
M300 P250 S750
G4 P250
M300 P285 S850
G4 P450
M300 P285 S850
G4 P285
M300 P625 S1100
G4 S1
M400

SnowCrash

If this is still relevant, these are my picks:

1
6
7
9
20

Thanks!

Coffee

@phaedrux THANKS !!!

resam

@SnowCrash did you follow all the recent Firmware releases?
As far as I can tall, all the picks you listed are already implemented to some degree.

@dc42 as this threads continues to grow and grow, I would recommend closing it, and opening a fresh one after 2.0 and 1.21.1 is released.

SnowCrash

@resam said in Firmware wishlist and priorities for Duet WiFi and Duet Ethernet:

@SnowCrash did you follow all the recent Firmware releases?
As far as I can tall, all the picks you listed are already implemented to some degree.

Thanks @resam! That's great news

To your question, I haven't been following the recent firmware releases for the simple reason that I only got my DuetWifi a short while ago and it already had the latest firmware already installed.

However, I'm definitely planning on doing so in the future.

kenblu24

1 & 2, 6, 8, 3

resam

@kenblu24 1, 6, 8, and 3 are already done. Please read the release notes of recent firmware updates.
2 will probably never make it due to memory & cpu restrictions.

kenblu24

@resam darn #2 would have been awesome to have. Sorry, haven't been keeping up with the updates.

denke

Can we please add to the wishlist?
-Improved motion planning as of:
https://forum.duet3d.com/topic/4802/6th-order-jerk-controlled-motion-planning
I really hope it will be available for deltas too...

-Print resume from a given layer (Maybe the user could set the printhead to the appropriate layer and hit resume) ... From that point the head would go up, heat, (prime?) and continue the print.
I know it's possible threw editing the resume file, but this would make it so much easier...

Thanks!