ToolBoard: 2 wires fan, heater fault and how to extrude ?
-
@Veti with S0 or S1 It work just when It is at 100% now. But not for all other value it don't work
-
@Pseud3mys
some fans do not work with pwm. -
@Veti I just see that is a 24v fan, I power the board with 12v. But if I power with 24v did the output will go up 24v as well ?
-
@Pseud3mys said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:
I power the board with 12v. But if I power with 24v did the output will go up 24v as well ?
no
see the wiring diagram.https://duet3d.dozuki.com/Wiki/Duet_3_Tool_Board
the out is 12v
-
ah yes, thank you
-
@Veti have you an idea for the heater fault or the cold extrusion ?
I send M302 P1 to allow cold extrusion, and I test if the command went good:
"Cold extrusion is allowed (use M302 P0 to forbid it)"but I still can't use it:
-
what is the error message in the console?
-
@Veti there are no error message. When I click on the "extrude" button nothing happen
-
@Pseud3mys
for the heating. how did you get the error?you still have not posted your config.g
-
@Veti for the heating a fault accure 2 or 3 sec after the start. But the temperature problem is good now.
here is my config..g:
config.g; Configuration file for Duet 3 (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.1.9 on Wed Dec 02 2020 17:31:45 GMT+0100 (heure normale d’Europe centrale) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"MultiTool Cartesian" ; set printer name ; Network M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0.0 S1 ; physical drive 0.0 goes forwards M569 P0.1 S1 ; physical drive 0.1 goes forwards M569 P0.2 S1 ; physical drive 0.2 goes forwards M569 P1.0 S1 ; physical drive 1.0 goes forwards M569 P2.0 S1 ; physical drive 2.0 goes forwards M584 X0.0 Y0.1 Z0.2 E1.0:2.0 ; set drive mapping M350 X256 Y256 Z256 E256:256 I0 ; configure microstepping without interpolation M92 X80.00 Y80.00 Z400.00 E420.00:420.00 ; set steps per mm M566 X900.00 Y900.00 Z60.00 E120.00:120.00 ; set maximum instantaneous speed changes (mm/min) M203 X31800.00 Y31800.00 Z31800.00 E1200.00:1200.00 ; set maximum speeds (mm/min) M201 X500.00 Y500.00 Z20.00 E250.00:250.00 ; set accelerations (mm/s^2) M906 X800 Y800 Z800 E800:800 ; set motor currents (mA) M84 S0 ; Disable motor idle current reduction ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X1000 Y1000 Z800 S0 ; set axis maxima ; Endstops ; WARNING: No endstops configured ; Z-Probe M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed M557 X20:980 Y20:980 S80 ; define mesh grid ; Heaters M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0 M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0 M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M308 S1 P"121.temp0" Y"thermistor" T500000 B4723 C1.19622e-7 ; configure sensor 1 as thermistor on pin 121.temp0 M950 H1 C"121.out0" T1 ; create nozzle heater output on 121.out0 and map it to sensor 1 M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit M143 H1 S280 ; set temperature limit for heater 1 to 280C M308 S2 P"122.temp0" Y"thermistor" T500000 B4723 C1.19622e-7 ; configure sensor 2 as thermistor on pin 122.temp0 M950 H2 C"122.out0" T2 ; create nozzle heater output on 122.out0 and map it to sensor 2 M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit M143 H2 S280 ; set temperature limit for heater 2 to 280C ; Fans M950 F0 C"121.out2" Q500 ; create fan 0 on pin 121.out2 and set its frequency M106 P0 S0 H1 T100 ; set fan 0 value. Thermostatic control is turned on M950 F1 C"122.out2" Q500 ; create fan 1 on pin 122.out2 and set its frequency M106 P1 S0 H2 T100 ; set fan 1 value. Thermostatic control is turned on ; Tools M563 P0 S"Extrudeur 0" D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C M563 P1 S"Extrudeur 1" D1 H2 F1 ; define tool 1 G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C M563 P2 S"Spindle" F-1 ; define tool 2 G10 P2 X0 Y0 Z0 ; set tool 2 axis offsets G10 P2 R0 S0 ; set initial tool 2 active and standby temperatures to 0C ; Custom settings are not defined ; Miscellaneous M501 ; load saved parameters from non-volatile memory -
@Pseud3mys said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:
for the heating a fault accure 2 or 3 sec after the start.
what is the error message for that.
M350 X256 Y256 Z256 E256:256 I0
this will overload your cpu. switch back to x16 and interpolation.
M203 X31800.00 Y31800.00 Z31800.00 E1200.00:1200.00
are you sure thats the maximum speed you printer can achieve?
M906 X800 Y800 Z800 E800:800 ; set motor currents (mA)
these values are most likely wrong. you need to enter 75% of the rated current for each motor.
; Endstops
; WARNING: No endstops configured
you need to fix this
-
I allowed the cold extrusion. I can now extrude but when I do it nothing happen.
For the heating, the thermistor return the right temperature. But I still have "fault" few second after I turn ON the heater. -
@Pseud3mys said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:
But I still have "fault" few second after I turn ON the heater.
we need to know what the error message is.
-
btw are you on firmware 3.1.1 ?
-
are you sure thats the maximum speed you printer can achieve?
No, I didn't begin setting up this part. Now, I just try to set up the dual extrudeur and hotends.
-
@Veti said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:
btw are you on firmware 3.1.1 ?
yes
-
@Veti said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:
we need to know what the error message is.
I understood, but I have no error message or I don't now where i can see it.
I click on "Heater 2". It turn active, and after fews seconds It turn "fault" as you can see on the picture. But I have no error (even in the consol) -
you can find the error messages in the console or in the popup at the bottom right when they occur.
-
@Veti said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:
you can find the error messages in the console or in the popup at the bottom right when they occur.
I just tested but I don't have any error message (I checked the console and there is no pupop when it stop working)
-
are you on duet web control 3.1.1 as well?
