Newbie: New Install on Ender 5 Plus---Willing to PAY$$$
-
Also, anyway of using the stock screen with the new Beta RR firmware? I saw it now supports 2 other screens. I dont know what chipset the stock screen has
-
do you have Heat-shrink tubing? or a solder iron.
fixing cut wiring is not that difficult -
@Veti said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
do you have Heat-shrink tubing? or a solder iron.
fixing cut wiring is not that difficultYes of course....Im in IT.
I would rather buy new cables with the 4 pin already on them.
-
They also have jacketed wire but not terminated. Better protection.
-
Im just gunna repair it. Not in the mood to change shit around. Let u know what happens tom night. Thanks for the help
-
Well guess what...............HOMING WORKS!!!! Went to the endstops and stopped! Question...Z axis...positive value is up or down? Z positive and the bed moves down. I have a feeling its supposed to be reversed. I repaired the wire on one of the Z stepper wires.
-
And the BLT is making the bed stop moving up so that works. Now I guess I have to do a test print and adjust the distance from the nozzle to the bed, make sure the BLT is working on leveling, extruder speed, and manual bed leveling before I use the BLT
-
@shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
Well guess what...............HOMING WORKS!!!! Went to the endstops and stopped! Question...Z axis...positive value is up or down? Z positive and the bed moves down. I have a feeling its supposed to be reversed. I repaired the wire on one of the Z stepper wires.
when the bed is at the bltouch trigger that is z=0 the further the bed moves away from the bltouch, z increases.
so for the ender 5 plus i think going down is positive -
@Veti said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
@shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
Well guess what...............HOMING WORKS!!!! Went to the endstops and stopped! Question...Z axis...positive value is up or down? Z positive and the bed moves down. I have a feeling its supposed to be reversed. I repaired the wire on one of the Z stepper wires.when the bed is at the bltouch trigger that is z=0 the further the bed moves away from the bltouch, z increases.
so for the ender 5 plus i think going down is positiveOK so its correct then. Whats my next step? BLT distance ? Extruder motor speed and stuff? I have a Micro Swiss direct drive all metal installed. I was reading the directions and they said 1 or 2 things have to be changed. As far as leveling, manual first then use the BLT? I guess use the wheel adjustments in each corner? How do I know when its correct? Should I use a level? Any way for the machine to tell me?
-
yes calibrate the z probe.
https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe#Section_Calibrate_the_Z_probe_trigger_heightthen do a mesh bed leveling and look at the bed. (post a picture)
then calibrate your e steps
https://duet3d.dozuki.com/Guide/Ender+3+Pro+and+Duet+Maestro+Guide+Part+4:+Calibration/40#s165then pid tune your bed and hotend.
https://duet3d.dozuki.com/Wiki/Tuning_the_heater_temperature_controlthen print a benchy and asses.
-
This post is deleted! -
All the steppers are quiet except the 2 Zs. Normal?
-
then print a benchy and asses.
You want me to print a replica of my ass? LOL
-
funny typo i mean assess.
what exactly do you mean by quiet?
stand still noise?
https://duet3d.dozuki.com/Wiki/Reducing_Stand-Still_Noise -
@Veti
When the Z's are going up and down during the mesh test, they are louder than others -
yes, z movement with a leadscrew is noisier than other movements.
-
I dunno why that corner is so off
-
@Veti Hows the bed leveling?
-
looks good, just dont printer on the borders of the bed, continue on.
-
Getting error on bed heat....saying its not rising fast enuf...1.7c a sec. I also have the bed connected to the mosfet that came with the stock setup.
