Need Probe Setup Help
-
remove lines 1 to 42 from your config file. they shouldn't be there
-
Interesting. Those lines do not show in my config.g. I am copying the config.g by selecting all, copy, paste. When I do that those other lines appear but I don't see them otherwise. Weird. ; generated by RepRapFirmware Configuration Tool v3.1.4 on Wed Sep 16 2020 09:55:19 GMT-0400 (Eastern Daylight Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Q5" ; set printer name M665 R104.3 L215 B180.8 H210 ; Set delta radius, diagonal rod length, printable radius and homed height M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S1 ; physical drive 0 goes forwards M569 P1 S1 ; physical drive 1 goes backwards M569 P2 S1 ; physical drive 2 goes forwards M569 P3 S1 ; physical drive 3 goes forwards M584 X0 Y1 Z4 E3 ; set drive mapping M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X80.00 Y80.00 Z80.00 E663.00 ; set steps per mm M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min) M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min) M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2) M906 X800 Y800 Z800 E600 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 Z0 S1 ; set minimum Z ; Endstops M574 X2 S1 P"xstop" ; configure active-high endstop for high end on X via pin xstop M574 Y2 S1 P"ystop" ; configure active-high endstop for high end on Y via pin ystop M574 Z2 S1 P"zstop" ; configure active-high endstop for high end on Z via pin zstop ; Z-Probe M558 P8 C"!io0.in" H5 F300 T6000 R0.4 ; set Z probe type to switch and the dive height + speeds G31 P500 X0 Y0 Z20.6 ; set Z probe trigger value, offset and trigger height M557 R52 S20 ; define mesh grid ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S100 ; set temperature limit for heater 0 to 100C M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 S1 H T45 ; set fan 0 value. Thermostatic control is turned on M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency M106 P2 S1 H1 T45 ; set fan 2 value. Thermostatic control is turned on ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C M501 ; Custom settings are not defined -
If you send M558, what does it output?
-
M558
Error: M558: Z probe 0 not found -
I've just realised why. You've used a duet 3 pin name with a duet 2.
Where do you have it connected? -
At position E0 on the endstop connectors
-
change your command to
M558 P8 C"!e0stop" H5 F300 T6000 R0.4 -
-
Before you ask:
m558
Z Probe 0: type 8, input pin !e0stop, output pin nil, dive height 5.0mm, probe speed 300mm/min, travel speed 6000mm/min, recovery time 0.44 sec, heaters normal, max taps 1, max diff 0.03 -
Run G30 and see if it probes.
I would make sure you've homed your machine using G28 and then tap the probe on the way down to make sure it stops -
@jay_s_uk
"Probe already triggered"Remove exclamation point from 558?
-
yes please
-
Great progress! G30 starts probe quite slowly, stops immediately when triggered and raises up a bit.
Do it again with probe? -
now you've got the height set you can G32 (assuming your bed file is correct)
-
Sorry - took a bit of doing, but G32 yields a 6 point probe. You are awesome. Now, M500?
-
@1d1 yep.
-
Excellent. Can I buy you a beer? Your time and effort is much appreciated.
-
No need. I prefer to see people being able to print
-
Well, great! Many thanks.
Interested in one more area I need some help with? Regarding Fan pins and activation...
-
Never mind - I actually found the problem on my own. Hard to believe.... !
Thanks again...
