Hot end not working after upgrade to RR3

Veti

@dingo007 said in Hot end not working after upgrade to RR3:

M563 P0 D0 H1 F0 ; define tool 0

you selefcted heater1 but you configured heater0

DIY-O-Sphere

@dingo007 said in Hot end not working after upgrade to RR3:

M308 S0 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin e0temp
M950 H0 C"e0heat" T0 ; create nozzle heater output on e0heat and map it to sensor 0
M143 H0 S280 ; set temperature limit for heater 0 to 280C
M307 H0 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit

H0 is the bed heater
You have to configure that for H1

blt3dp

This line, you define the tool to use heater 1 which doesn't exist

M563 P0 D0 H1 F0 ; define tool 0

Try

M563 P0 D0 H0 F0 ; define tool 0

DIY-O-Sphere

@blt3dp
Bad idea....

dingo007

modified as suggested and still not functioning ....
; Heaters
M140 H-1 ; disable heated bed (overrides default heater mapping)
M308 S0 P"e0temp" Y"thermistor" T100000 B4138 C7.06e-8 R4700 ; configure sensor 0 as thermistor on pin e0temp
M950 H1 C"e0heat" T0 ; create nozzle heater output on e0heat and map it to sensor 0
M143 H1 S280 ; set temperature limit for heater 0 to 280C
M307 H1 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H0 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

DIY-O-Sphere

@dingo007 said in Hot end not working after upgrade to RR3:

M308 S0

Check that too

dingo007

@DIY-O-Sphere still no joy after modifying the config

1/10/2020, 11:01:08 PM M292 P1
Printing paused at X0.0 Y0.0 Z0.0
1/10/2020, 11:01:06 PM Resume state saved
Warning: Tool 0 was not driven because its heater temperatures were not high enough or it has a heater fault
1/10/2020, 11:01:01 PM Error: Temperature reading fault on heater 1: unknown temperature sensor channel

with config.g
; Heaters
M140 H-1 ; disable heated bed (overrides default heater mapping)
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 C7.06e-8 R4700 ; configure sensor 0 as thermistor on pin e0temp
M950 H1 C"e0heat" T0 ; create nozzle heater output on e0heat and map it to sensor 0
M143 H1 S280 ; set temperature limit for heater 0 to 280C
M307 H1 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H0 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

Veti

@dingo007 said in Hot end not working after upgrade to RR3:

M950 H1 C"e0heat" T0 ; create nozzle heater output on e0heat and map it to sensor 0

change to T1.

it would be easier if you did this in the configurator.

dingo007

@Veti that configurator is too confusing, probably why i got where i am... and it was generated in RR config

dingo007

@Veti

Nope no joy.... maybe RR3 was abad idea

Printing paused at X0.0 Y0.0 Z0.0
1/10/2020, 11:07:15 PM Error: Temperature reading fault on heater 1: unknown temperature sensor channel
Resume state saved
Warning: Tool 0 was not driven because its heater temperatures were not high enough or it has a heater fault

config.g
; Heaters
M140 H-1 ; disable heated bed (overrides default heater mapping)
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 C7.06e-8 R4700 ; configure sensor 0 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 0
M143 H1 S280 ; set temperature limit for heater 0 to 280C
M307 H1 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H0 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

blt3dp

@DIY-O-Sphere

What do you mean? He's was heater 0 as his hotend heater, his tool was set to use heater 1 all that I suggested was to tell the tool definition to use the correct heater.

I do suppose you could change everything to heater 1 as was done, I would have just changed that one line to heater 0 instead.

Looking at your current config, it should work.

dingo007

Does this bother anyone else?? Current 2000.0c

Veti

@dingo007
did you reststart after changing the config?

dingo007

@Veti yes, i always restart after any edits.... even single character edits.

Veti

@dingo007
2000 means there is no thermistor on that connector also delete the C

also your thermistors values are incorrect.

DIY-O-Sphere

@blt3dp
Noone else would understand why H0 is used for the tool.
To comply with conventions I think it's better not to do that.

dingo007

@Veti

working RR2 config.g
; Heaters
M140 H-1 ; disable heated bed
M305 P1 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

non-working RR3 config.g
; Heaters
M140 H-1 ; disable heated bed (overrides default heater mapping)
M308 S0 P"e0temp" Y"thermistor" T100000 B4138 R4700 ; configure sensor 0 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 0
M143 H1 S280 ; set temperature limit for heater 0 to 280C
M307 H1 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H0 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

Veti

; Heaters
M140 H-1 ; disable heated bed (overrides default heater mapping)
M308 S0 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin e0temp
M950 H0 C"e0heat" T0 ; create nozzle heater output on e0heat and map it to sensor 0
M143 H0 S280 ; set temperature limit for heater 0 to 280C
M307 H0 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit

; Tools
M563 P0 D0 F0 ; define tool 0

add it this way

Veti

@Veti said in Hot end not working after upgrade to RR3:

M563 P0 D0 F0 ; define tool 0

sorry
M563 P0 D0 H0 F0 ; define tool 0

seems there is a problem with the configurator.

dingo007

@Veti said in Hot end not working after upgrade to RR3:

M563 P0 D0 H0 F0 ; define tool 0

1/10/2020, 11:38:54 PM Printing paused at X0.0 Y0.0 Z0.0
1/10/2020, 11:38:52 PM Resume state saved
Warning: Tool 0 was not driven because its heater temperatures were not high enough or it has a heater fault
1/10/2020, 11:38:47 PM Error: Temperature reading fault on heater 0: unknown temperature sensor channel

config.g - edited as you said.
; Heaters
M140 H-1 ; disable heated bed (overrides default heater mapping)
M308 S0 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin e0temp
M950 H0 C"e0heat" T0 ; create nozzle heater output on e0heat and map it to sensor 0
M143 H0 S280 ; set temperature limit for heater 0 to 280C
M307 H0 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H0 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H0 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C