Mesh calibration not working or what am I doing wrong?

Dep

Made a calibration with the parameters: M557 X500:700 Y150:230 S20

RepRapFirmware height map file v2 generated at 2019-11-03 18:06, min error -0.633, max error -0.047, mean -0.346, deviation 0.137
xmin,xmax,ymin,ymax,radius,xspacing,yspacing,xnum,ynum
500.00,700.00,150.00,230.00,-1.00,20.00,20.00,11,5
 -0.329, -0.318, -0.282, -0.248, -0.238, -0.218, -0.195, -0.176, -0.133, -0.089, -0.047
 -0.377, -0.358, -0.342, -0.314, -0.324, -0.287, -0.280, -0.235, -0.199, -0.162, -0.118
 -0.484, -0.434, -0.434, -0.435, -0.375, -0.344, -0.337, -0.308, -0.259, -0.216, -0.163
 -0.541, -0.507, -0.491, -0.479, -0.467, -0.427, -0.433, -0.389, -0.338, -0.282, -0.226
 -0.633, -0.607, -0.580, -0.550, -0.533, -0.510, -0.484, -0.463, -0.407, -0.353, -0.298

I still can’t understand what this can give us?

Dep

@fcwilt Bed Size X1380 Y1210
I only calibrate 500 x 500

But the part fits in this size. It is inside a calibrated space.

Do you think if not the entire bed is calibrated this can cause an error? But how to do that? Maybe reduce the table and set offsets?

fcwilt

@Dep said in Mesh calibration not working or what am I doing wrong?:

@fcwilt Bed Size X1380 Y1210
I only calibrate 500 x 500

But the part fits in this size. It is inside a calibrated space.

Do you think if not the entire bed is calibrated this can cause an error? But how to do that? Maybe reduce the table and set offsets?

One height map you posted was absolutely terrible.

I just want to get picture of the entire bed as a reference.

Not having the entire bed calibrated shouldn't cause an error unless you try to print outside that area.

But there is not much point in having a large bed if you cannot use it all.

Thanks.

Frederick

Dep

@fcwilt said in Mesh calibration not working or what am I doing wrong?:

One height map you posted was absolutely terrible.
I just want to get picture of the entire bed as a reference.
Not having the entire bed calibrated shouldn't cause an error unless you try to print outside that area.
But there is not much point in having a large bed if you cannot use it all.

Now I can’t make a height map of the whole table, because glass 650 x 650 mm is fixed on the table

Yes, the bed is very crooked. But why doesn't compensation work? Does it really matter how rough the bed is?

Veti

@Dep said in Mesh calibration not working or what am I doing wrong?:

Does it really matter how rough the bed is?

with a bed as uneven as that it does.
the points in beetween probing are calculated and dont reflect what is actually there.
so if the bed is not uniformly uneven it will be off.
with it beeing off by an entire layer means this error can be significant.

Dep

Yes, I agree, but the table is made of 4mm glass. It cannot be a “spasmodic” curve. I hope I wrote correctly

Those. the glass of course bends around the table, but these are smooth bends.

fcwilt

@Dep said in Mesh calibration not working or what am I doing wrong?:

Now I can’t make a height map of the whole table, because glass 650 x 650 mm is fixed on the table

Yes, the bed is very crooked. But why doesn't compensation work? Does it really matter how rough the bed is?

I see. Have you probed the glass area? Have you posted the height map here?

If you are limited to 121 points its going to be hard to get an accurate picture of that area

Probe a 220 by 220 area in the center of the glass and post the height map please.

Frederick

Dep

Ok, did it:

RepRapFirmware height map file v2 generated at 2019-11-03 19:31, min error -1.658, max error -0.124, mean -0.815, deviation 0.349
xmin,xmax,ymin,ymax,radius,xspacing,yspacing,xnum,ynum
600.00,800.00,300.00,500.00,-1.00,20.00,20.00,11,11
 -0.817, -0.773, -0.734, -0.627, -0.614, -0.546, -0.462, -0.402, -0.332, -0.225, -0.124
 -0.884, -0.839, -0.803, -0.752, -0.669, -0.608, -0.543, -0.447, -0.357, -0.249, -0.197
 -0.951, -0.911, -0.876, -0.794, -0.727, -0.650, -0.593, -0.466, -0.392, -0.303, -0.221
 -1.018, -0.982, -0.927, -0.866, -0.784, -0.719, -0.652, -0.532, -0.477, -0.361, -0.230
 -1.112, -1.084, -1.003, -0.936, -0.846, -0.780, -0.662, -0.569, -0.475, -0.394, -0.303
 -1.191, -1.137, -1.079, -1.004, -0.908, -0.821, -0.727, -0.628, -0.552, -0.449, -0.337
 -1.293, -1.210, -1.157, -1.087, -1.000, -0.896, -0.788, -0.681, -0.595, -0.441, -0.354
 -1.398, -1.303, -1.233, -1.160, -1.062, -0.968, -0.864, -0.753, -0.645, -0.521, -0.419
 -1.490, -1.404, -1.323, -1.231, -1.137, -1.033, -0.924, -0.789, -0.704, -0.581, -0.453
 -1.544, -1.474, -1.409, -1.314, -1.201, -1.101, -0.995, -0.886, -0.752, -0.614, -0.506
 -1.658, -1.574, -1.497, -1.390, -1.277, -1.162, -1.050, -0.925, -0.774, -0.658, -0.533

Offset down because the table is not heated now

Veti

please post the images as well

Dep

Veti

if you have a sloping x gantry the probe will be at an tilt angle. this will cause errors in the measurements as well.

Phaedrux

I would suggest slowing down the probe speed of the BLTouch from 300 to 100. It's possible you're getting some bad probe points.

Are you able to manually level the bed with adjustment screws? It looks like there is a large amount of tilt.

The limited number of probe points with the older Duet board is going to make it difficult to get an accurate heightmap of such a large bed. The area between points is interpolated, but unless the surface is very flat to begin with, the risk is there for the interpolation to gloss over a defect.

Possible work around would be to modify your first layer parameters to compensate for the unevenness by using extra thick extrusion. Or perhaps using a raft.

Dep

I use M558 P9 H6 F300 T6000 R0.2 A5 B1 - where A5 - five times probe and usually it probe just 2 times, theni think bltouch work well. But i will test lower down speed of probing.

I agree that the table is very crooked and 50mm is a lot.

But look at the photo - there part of the model is at least have 3-4 points. Why is there no compensation?

Veti

@Dep said in Mesh calibration not working or what am I doing wrong?:

Why is there no compensation?

there is. your bed has a 1mm diffrence between both sides.

turn off compensation and print one without.

fcwilt

Hi,

Well at least the section seems pretty smooth even if badly tilted.

There are things you may be doing at the start of the print that are disabling mesh compensation.

Does the DWC interface show that mesh compensation is on? You can verify this during a print.

Frederick

infiniteloop

@Dep Looking at the last two height maps you published, just one corner matches the plane which the firmware assumes to be the bed’s surface. Interestingly, the height map itself is quite consistent, i.e. relatively flat. It is just not in sync with the bed level. In order to cure this, you really should carefully level your bed and then calibrate Z=0 at its center, before you run another mesh grid calibration. As long as the resulting height map is not (at least partially) in sync with the assumed bed plane, it’s useless.

Dep

@fcwilt Yes, compensation is on. I checked the M122 command, and also it is visible since the bed moves up / down when printing.

Dep

@infiniteloop What do you mean by synchronizing with the bed?

If you mean the transition through zero, then it is when the bed is heated.

I can’t level the bed better, it is very big and heavy. And when I heat it to 120 degrees - it distorts it a lot.

Also, when the entire chamber is heated to 45 - 50 degrees, the entire system also bends.

But I do this: I warm up the bed and chamber , wait 1-2 hours and run mesh calibration two times and compare the resulting grid. If everything is ok, I'm trying to print. This is a very long process

But every time the same thing.

I don’t understand why mesh cannot perform compensation.

jens55

@Dep, maybe I can put it in slightly different words that might make more sense.

Suppose you have 50 mm between probing points. Also suppose you are printing a part that is 50 mm long and starts on probing point one and goes to probing point two.

The mesh compensation interprets the area between point one and point two as a straight line so let's suppose point one is at 0.1 mm and point two is 0.5 mm for the offset. This means that the Duet thinks that the height at 25 mm is 0.3 mm.
The problem is that this is a guess. With a very uneven bed, your actual offset in the middle might be -0.1 or + 1.0 or whatever. The controller does not and can not know about what is actually happening in an area that was not probed and has to make an educated guess. If that guess does not reflect the true shape of the actual bed then you get a strange print.

Another way of looking at it is the mesh bed levelling can only work reasonably well if the bed does not vary wildly between probing points. It can compensate nicely if you have sufficient probing points so that the height between two adjacent probing points does not vary by a lot and the interpolation that happens between the two points can reasonably be described as a relatively straight line.

Hope that helps ....

Edit: If you were printing a model that is 50 mm * 50 mm and if you used all 121 available probe points for that small printing area, you would likely get a very nice first layer.

deckingman

@jens55 I agree in theory with what you say but from what I can gather, @Dep has a sheet of 4mm glass on top of "something" - presumably an aluminium heat spreader of some sort. In which case, I'd have thought that it's very unlikely that there are any significant peaks and troughs between any two 50mm probe points and the glass would have a fairly even curvature. In which case, interpolation between points should be reasonably accurate.