Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    cr-10s upgrade to duet 2 wifi motors and ac 750w bed problems

    Scheduled Pinned Locked Moved
    General Discussion
    6
    39
    2.0k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • jobesynoob1234undefined
      jobesynoob1234
      last edited by

      Hi there i hope someone here can help me :(. I seem to have a few problems at the moment i am upgrading my cr-10s with the duet 2 wifi with a ac powered 230v 750w bed im using a KZLTD KS1-25da SSR i have everything wired but cant get steppers working and my heated bed starts heating up but then i get the "heating up to slow" error i have changed the heat up time from 180 to 195 seconds my hotend heats up no problem my endstops work when pressed i get the "yes" i have sent the

      G91
      G1 S2 X-10

      G91
      G1 S2 Y-10

      G91
      G1 S2 Z-10

      commands and they move my motors but they still wont home 😕 i have swapped the motor connections aroung in case it was that but still the same thing :(i am using a 12v power supply hope i havent left anything out 🙂 thaks for any advice.

      1 Reply Last reply Reply Quote 0
      • Vetiundefined
        Veti
        last edited by

        post All your configurations

        1 Reply Last reply Reply Quote 0
        • jobesynoob1234undefined
          jobesynoob1234
          last edited by

          sorry but how do i do that 😕 im a right noob

          1 Reply Last reply Reply Quote 0
          • jobesynoob1234undefined
            jobesynoob1234
            last edited by

            is that the config.g file??

            dragonnundefined 1 Reply Last reply Reply Quote 0
            • dragonnundefined
              dragonn @jobesynoob1234
              last edited by

              @jobesynoob1234 yes and all homing files too

              1 Reply Last reply Reply Quote 0
              • jobesynoob1234undefined
                jobesynoob1234
                last edited by

                ; Configuration file for factory testing Duet Ethernet and Wifi with V2.02 firmware

                FOR TESTING ONLY! USE https://configurator.reprapfirmware.org/ to generate configuration files for your printer!

                ; Communication and general
                M111 S0 ; Debug off
                M550 PDuetTest ; Machine name and Netbios name (can be anything you like)
                M551 Preprap ; Machine password (used for FTP)

                *** Ethernet networking: The following lines are used for factory testing - PLEASE REMOVE THEM
                M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0xED ; MAC Address
                M552 P192.168.1.14 ; IP address
                M554 P192.168.1.255 ; Gateway
                M553 P255.255.255.0 ; Netmask

                ;*** End of factory test lines to be removed

                ;*** Networking
                M552 S1 ; Turn network on

                M555 P2 ; Set output to look like Marlin
                G21 ; Work in millimetres
                G90 ; Send absolute coordinates...
                M83 ; ...but relative extruder moves

                ; Disable Fan 1 thermostatic mode
                M106 P1 H-1

                ; Axis and motor configuration
                M569 P0 S1 ; Drive 0 goes forwards
                M569 P1 S1 ; Drive 1 goes forwards
                M569 P2 S1 ; Drive 2 goes forwards
                M569 P3 S1 ; Drive 3 goes forwards
                M569 P4 S1 ; Drive 4 goes forwards
                M574 X2 Y2 Z2 S1 ; set endstop configuration (all endstops at high end, active high)
                ;*** The homed height is deliberately set too high in the following - you will adjust it during calibration
                M665 R105.6 L215.0 B85 H250 ; set delta radius, diagonal rod length, printable radius and homed height
                M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them
                M350 X16 Y16 Z16 E16:16 I1 ; Set 16x microstepping with interpolation
                M92 X80 Y80 Z400 ; Set axis steps/mm
                M906 X1000 Y1000 Z100 E750 I60 ; Set motor currents (mA) and increase idle current to 60%
                M201 X3000 Y3000 Z100 E1000 ; Accelerations (mm/s^2)
                M203 X20000 Y20000 Z20000 E3600 ; Maximum speeds (mm/min)
                M566 X1200 Y1200 Z1200 E1200 ; Maximum instant speed changes mm/minute

                ; Thermistors
                M305 P0 T100000 B3950 R4700 H120 L0 ; Put your own H and/or L values here to set the bed thermistor ADC correction
                M305 P1 T100000 B3974 R4700 H300 L0 ; Put your own H and/or L values here to set first nozzle thermistor ADC correction
                M305 P2 T100000 B3974 R4700 H30 L0 ; Put your own H and/or L values here to set 2nd nozzle thermistor ADC correction

                M570 S195 ; Hot end may be a little slow to heat up so allow it 180 seconds

                ; Adjustments for dummy heaters on test rig
                M307 H0 A250 C140 D5.5 B1
                M307 H1 A250 C140 D5.5 B0
                M307 H2 A250 C140 D5.5 B0

                ; Fans
                M106 P1 S-1 ; disable thermostatic mode for fan 1

                ; Tool definitions
                M563 P0 D0 H1 ; Define tool 0
                G10 P0 S0 R0 ; Set tool 0 operating and standby temperatures
                ;*** If you have a single-nozzle build, comment the next 2 lines
                //M563 P1 D1 H2 ; Define tool 1
                //G10 P1 S0 R0 ; Set tool 1 operating and standby temperatures
                M92 E80:80 ; Set extruder steps per mm

                ; Z probe and compensation definition
                ;*** If you have a switch instead of an IR probe, change P1 to P4 in the following M558 command.
                M558 P4 F100 T6000 X0 Y0 Z0 H3 ; Z probe is a Smart Effector and is not used for homing any axes R0.4 not used. Reduced F300 to 100
                G31 P100 X0 Y0 Z-0.25 ; Set the zprobe height and threshold for Smart Effector

                ;*** If you are using axis compensation, put the figures in the following command
                M556 S78 X0 Y0 Z0 ; Axis compensation here

                M208 S1 Z-0.2 ; set minimum Z

                T0 ; select first hot end
                ; M117 Use https://configurator.reprapfirmware.org/ to set up your printer config

                1 Reply Last reply Reply Quote 0
                • jobesynoob1234undefined
                  jobesynoob1234
                  last edited by

                  @dragonn said in cr-10s upgrade to duet 2 wifi motors and ac 750w bed problems:

                  homing files

                  homing files?? where are they 😕

                  1 Reply Last reply Reply Quote 0
                  • dragonnundefined
                    dragonn
                    last edited by

                    You should really read the first line of you config file.

                    1 Reply Last reply Reply Quote 0
                    • jobesynoob1234undefined
                      jobesynoob1234
                      last edited by

                      think i found them 🙂 ; Example Homing file for RepRapFirmware on delta printer

                      M117 Use https://configurator.reprapfirmware.org/ to set up your printer config

                      ;G91 ; use relative positioning
                      ;******* Change F250 in the following line to F2500 when you are finished commissioning
                      ;******* Change 320 in the following to a higher value if your Kossel has taller towers
                      ;G1 S1 X320 Y320 Z320 F2500 ; move all carriages up 320mm, stopping at the endstops
                      ;G1 S2 X-3 Y-3 Z-3 ; move all carriages down 3mm
                      ;G1 S1 X6 Y6 Z6 F250 ; move carriages slowly up 6mm, stopping at the endstops
                      ;G1 Z-5 F2000 ; down a few mm so that we can centre the head
                      ;G90 ; back to absolute positioning
                      ;G1 X0 Y0 F2000 ; centre the head and set a reasonable feed rate

                      1 Reply Last reply Reply Quote 0
                      • jobesynoob1234undefined
                        jobesynoob1234
                        last edited by

                        i have used the reprap configuration tool and as far as i know i uploaded it to the duet 😕 is that what u mean ?

                        dragonnundefined 1 Reply Last reply Reply Quote 0
                        • jobesynoob1234undefined
                          jobesynoob1234
                          last edited by

                          Duet2CombinedFirmware.bin is the file i believe 😕

                          dragonnundefined 1 Reply Last reply Reply Quote 0
                          • dragonnundefined
                            dragonn @jobesynoob1234
                            last edited by

                            @jobesynoob1234 yes, it seems that you did upload it wrong, maybe into the g-code page and not into system.
                            Pleas post what firmware version are you running (Main firmware, Wifi Server and Web Control)

                            1 Reply Last reply Reply Quote 0
                            • dragonnundefined
                              dragonn @jobesynoob1234
                              last edited by

                              @jobesynoob1234 No it is not, this is a file for updating the firmware, not configuring it.

                              1 Reply Last reply Reply Quote 0
                              • jobesynoob1234undefined
                                jobesynoob1234
                                last edited by

                                Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
                                Firmware Electronics: Duet WiFi 1.02 or later
                                Firmware Version: 2.02(RTOS) (2018-12-24b1)
                                WiFi Server Version: 1.22
                                Web Interface Version: 1.22.5

                                1 Reply Last reply Reply Quote 0
                                • dragonnundefined
                                  dragonn
                                  last edited by

                                  Pleas post the zip. file what you are getting from the reprap configuration and make some screens how do you upload it.

                                  1 Reply Last reply Reply Quote 0
                                  • jobesynoob1234undefined
                                    jobesynoob1234
                                    last edited by

                                    how do i upload the firmware because its saying i cant upload it in that format 😕

                                    1 Reply Last reply Reply Quote 0
                                    • jobesynoob1234undefined
                                      jobesynoob1234
                                      last edited by

                                      i mean how do i post it 😕 sorry

                                      1 Reply Last reply Reply Quote 0
                                      • Vetiundefined
                                        Veti
                                        last edited by

                                        @jobesynoob1234 said in cr-10s upgrade to duet 2 wifi motors and ac 750w bed problems:

                                        M665 R105.6 L215.0 B85 H250 ; set delta radius, diagonal rod length, printable radius and homed height
                                        M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them

                                        thats a delta printer configuration.

                                        please discard all your configs and start from new with the configurator

                                        1 Reply Last reply Reply Quote 0
                                        • jobesynoob1234undefined
                                          jobesynoob1234
                                          last edited by

                                          oooops that sounds like a big mistake 😕 what will i do now 😕 ????

                                          1 Reply Last reply Reply Quote 0
                                          • jobesynoob1234undefined
                                            jobesynoob1234
                                            last edited by

                                            do i select the corexy?

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA