Upgrading from Anet board with Auto leveling

wupinstick

So could I use the 5v from the panel connector?
Then use the zprobe signal and ground pins?
Or would I connect the probe to the z endstop connector like I have it on the Anet board?
https://imgur.com/gallery/izfo9

number40fan

https://ibb.co/n7UAuv

To the 5v on the right.

wupinstick

Where would I plug in my sensor? The E0 stop, z stop or zprobe?

FYI I just ordered the duet wifi!!

dc42

The outer 2 pins of the E0 endstop would be best.

wupinstick

Thanks! I'm sure I'll have more questions once my board arrives!

wupinstick

Ok so I just received my duet wifi!! I have setup the wifi and am able to access the web interface. I was going through the RepRapFirmware Configuration Tool and had some questions on translating my marlin settings.
I have provided links below that shows comparisons between marlin and the config tool.

http://imgur.com/XmuD66n config tool motor settings
http://imgur.com/mN9kzqM marlin motor settings

http://imgur.com/lA1gy2o config tool endstop settings
http://imgur.com/2wqDuZv marlin endstop settings
http://imgur.com/9gsdyXs marlin z probe settings

wupinstick

I think I have everything setup. the only thing I'm having issues with is the zprobe.
I have the zprobe wired up as dc42 suggested.
the gnd and signal pins from my sensor are wired to E0 endstop connections E0 stop and GND.
I have the 5v for my sensor connected to the 5V expansion connector pin 1.
when trying to run G29 I keep getting this error

Error: No valid grid defined for G29 bed probing

Below are some of my config settings for the z probe and my bed.g file

thanks for all of the help.

[[language]]
; General preferences
M111 S0                                         ; Debugging off
G21                                             ; Work in millimetres
G90                                             ; Send absolute coordinates...
M83                                             ; ...but relative extruder moves
M555 P2                                         ; Set firmware compatibility to look like Marlin
M208 X-14 Y0 Z0 S1                                 ; Set axis minimum set so x0 y0 is at corner of bed x=-14
M208 X220 Y220 Z240 S0                            ; Set axis maximum

; ????????? not sure about zprobe configuration 

; Endstops
M574 X1 Y1 Z0 S0                                 ; Define active low and unused microswitches

;zprobe section ??????????
M558 P4 X0 Y0 Z1 H5 I1 F120 T6000                     ; Set Z probe type to switch, the axes for which it is used and the probe + travel speeds
G31 X0 Y53 Z2                                     ; Set Z probe offset and trigger height see end of this file.

bed.g file

[[language]]
M561						;Clear any bed transform
G28							;Home all axes
M557 X10:210 Y53:210 S40 	;Define mesh grid 
G29 S0						;Probe the bed and save height map to file
M374 						; Save calibration data. Default is sys/heightmap.csv

wupinstick

I think i found my problem. Let me know if I'm right.

When setting up the grid with M557 I should subtract the z probe y offset (53) from my current numbers.
I believe it should look like this: M557 X10:210 Y0:157 S40

dc42

You don't need to subtract the Z probe offset, however any points that are not reachable by the Z probe will not be probed.

My guess is that you had a typo in your M557 command.

wupinstick

Thanks for the help. I have everything working now!
just as a reference below are my zprobe and bed.g configs

Z-Probe

[[language]]
M558 P4 X0 Y0 Z1 H2 I1 F120 T6000 
G31 P1000 X0 Y53 Z6.582

bed.g file

[[language]]
M561				
G28				
G90 	
M557 X10:210 Y0:210 S40
G29 S0				
M374

dc42

You don't need the M374 command, the G29 S0 command will save to heightmap.csv anyway.