@oliof said in 3.3b1 SBC KISS slicer filament usage and print time estimates:

Hi,
KISS Slicer 2.0 alpha 6 filament usage and print time estimates aren't detected by 3.3b1 in SBC mode.

Attached is a sample file so filters can be adjusted.

(I guess this goes to @chrishamm again)

sample_cube-KISS.gcode

I have confirmed that this file is already analysed correctly in standalone mode.

d971b9df-d997-4a58-8c71-79d0611d9382-image.png

Done in standalone mode:

0074ca6f-1092-4a91-aa54-62a6c8a4097b-image.png

Thanks, I've got an update ready for this format, too.

hi @chrishamm,
I can confirm these changes work in SBC mode.

@ctilley79 said in 3.3b1CAN timeout resets itself?:

I may have screwed this up. So It's best to power the 3HC from the 6HC Mainboard instead of running a separate wire from the PSU? Why?

It only matters if you are powering a high-powered bed heater directly from the Duet and you have long wires between the Duet and the PSU. Under those conditions, the changes in ground voltage caused by the bed heater being switching on/off rapidly with PWM can affect the CAN communication.

@garyd9 said in Bug in 3.2.2: X/Y/Z positioning wrong in DWC and PanelDue:

Of course, now that you've told me switching to machinePosition is as trivial as a click, I might not care. 😉 I wonder if @wilriker would be willing to add a similar toggle to PanelDue.

I intend to provide this possibility but due to the limited screen estate I have to carefully work out where I can make space for a button or similar.

@dc42! Thank you for uploading the Sammy Firmware. It was an easy install and it seems to be working.
BTW, it is not part of the ZIP files in the repository, you have to get it manually. Thank you again for everything you do here!!!

I've compiled a stable 3.2.2. firmware (Duet 3 Mini 5+) with the TMC22xx.cpp fix from 3.3b1, so sensorless homing does work without loud crashing 😃
Now, after 2-3 full days of experimenting, time to enjoy this nice new board a bit.

If anyone needs it, here you go: https://www.file-upload.net/download-14505164/Duet3Firmware_Mini5plus.uf2.zip.html

I can confirm pause does not work as intended with 3.3 beta 1.

My print does halt in place but the contents of pause.g are not run.

Post a schematic showing how the optocoupler is connected.

If the optocoupler is leaky then you might need to add an external pullup resistor between IN and +3.3V on the Z Probe connector.

@gloomyandy

Yes that fixed the problem.

Thank you

Hmm, well after some more prints still on 3.1.1 I got the layer shifting again. So I guess the problem is something else...

Thanks @deckingman

Yes, i run a config_override, and i don't have any PID set in the config.g for my hotend, unfortunately, i'm not allowed to mention my hotend ^^

Sorry for showing my ignorance of delta machines. Not intended to hijack. Back to topic. Thanks for the report. Will move to the beta forum for further investigation.

@dc42 Ohhh thankyou i did not know that i was just using the info from my generator and my well pump starting load vs running load lol

@jay_s_uk

The Datasheet I was given does not Mention any Required Timing. It just says it accepts from 0-200Khz Pulse Frequency.

JSS57P2N Instruction manual

After Changing Timing to T5:5:5:5 and T10:10:10:10, It Seams to Move Fine, But there is Some Type Of error Accumulating. (Or somthing else, lol)

Yesterday, I was Getting Homing Errors. Today Without Changing Anything, Its Homing Fine, But Not waiting for the Hotend to Heatup before Moving. And Look at this Picture of a No Infill Cube. The Infill Filled in Slightly Wavy at the Bottom.

IMG_1942.jpg

@dc42

Just Tried Out your Request with 3.3Beta1

G91 G1 H2 X10 - Moved X10 Y10
G91 G1 H2 X-10 - Moved X-10 Y-10
G91 G1 H2 Y10 - Moved X10 Y-10
G91 G1 H2 Y-10 - Moved X-10 Y10

All Movements were Diagonal. These Movements Seem Unexpected.

Side Note: Changing the Timing to

M569 P40.0 S1 R0 T10:10:10:10 M569 P41.0 S1 R0 T10:10:10:10

Or T5:5:5:5 Seamed to make the Homing Error Go away. Machine now Homes No Issue.