m122 === Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.6.0-alpha.2+3 (2024-07-17 20:03:21) running on Duet WiFi 1.02 or later Board ID: 0JD2M-9F8TA-GJ4TD-6J1D6-3SD6P-16PG6 Used output buffers: 3 of 26 (23 max) === RTOS === Static ram: 23368 Dynamic ram: 68644 of which 0 recycled Never used RAM 3768, free system stack 102 words Tasks: NETWORK(1,ready,19.3%,195) HEAT(3,nWait 5,0.1%,309) Move(4,nWait 5,0.0%,272) MAIN(1,running,80.6%,716) IDLE(0,ready,0.0%,29), total 100.0% Owned mutexes: WiFi(NETWORK) USB(MAIN) === Platform === Last reset 00:26:27 ago, cause: software Last software reset at 2024-07-19 19:46, reason: User, Gcodes spinning, available RAM 13680, slot 2 Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a Error status: 0x00 Aux0 errors 0,0,0 MCU temperature: min 29.8, current 30.6, max 30.8 Supply voltage: min 1.7, current 25.0, max 25.2, under voltage events: 1, over voltage events: 0, power good: yes Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/168/168, gc cycles 0 Events: 0 queued, 0 completed Date/time: 2024-07-19 20:12:42 Slowest loop: 8.13ms; fastest: 0.14ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Storage === Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest read time 0.4ms, write time 0.0ms, max retries 0 === Move === Segments created 929, maxWait 0ms, bed comp in use: mesh, height map offset 0.000, hiccups added 0 (0.00ms), max steps late 0, ebfmin 0.00, ebfmax 0.00, mcet 0.000 Pos req/act/dcf: 29199.00/29199/1.00 -28400.00/-28400/-0.01 320229.00/320229/1.00 no step interrupt scheduled === DDARing 0 === Scheduled moves 77846, completed 77846, LaErrors 0, Underruns [0, 0, 0] Driver 0: standstill, SG min n/a Driver 1: standstill, SG min n/a Driver 2: standstill, SG min n/a Driver 3: standstill, SG min n/a Driver 4: standstill, SG min n/a Driver 5: Driver 6: Driver 7: Driver 8: Driver 9: Driver 10: Driver 11: === Heat === Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0 Heater 0 is on, I-accum = 0.1 === GCodes === Movement locks held by null HTTP is idle in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is ready with "m122" in state(s) 0 Aux is idle in state(s) 0 Trigger is idle in state(s) 0 Queue is idle in state(s) 0 LCD is idle in state(s) 0 Daemon is idle in state(s) 0 Autopause is idle in state(s) 0 Q0 segments left 0 Code queue 0 is empty === Network === Slowest loop: 21.07ms; fastest: 0.07ms Responder states: HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) HTTP sessions: 2 of 8 === WiFi === Interface state: active Module is connected to access point Failed messages: pending 0, notrdy 0, noresp 0 Firmware version 2.1.0 MAC address a4:e5:7c:03:da:81 Module reset reason: Power up, Vcc 3.41, flash size 2097152, free heap 42752 WiFi IP address 192.168.1.197 Signal strength -45dBm, channel 11, mode 802.11n, reconnections 0 Clock register 00002002 Socket states: 0 0 0 0 0 0 0 0 ok m111 p4 d1 b2048 Debugging enabled for modules: Move(4 - 0x1) Debugging disabled for modules: Platform(0) Network(1) Webserver(2) Gcodes(3) Heat(5) Kinematics(6) InputShaping(7) unused(8) PrintMonitor(9) Storage(10) PortControl(11) DuetExpansion(12) FilamentSensors(13) WiFi(14) Display(15) SbcInterface(16) CAN(17) Expansion(18) Leadscrew adjustments made: -0.299 -0.327, points used 2, (mean, deviation) before (-0.312, 0.012) after (0.000, 0.000) Leadscrew adjustments made: 0.004 0.002, points used 2, (mean, deviation) before (0.003, 0.001) after (-0.000, 0.000) Warning: the height map has a substantial Z offset. Suggest use Z-probe to establish Z=0 datum, then re-probe the mesh. 25 points probed, min error 0.282, max error 0.494, mean 0.399, deviation 0.062 Height map saved to file 0:/sys/heightmap.csv Done printing file Finished printing file 0:/gcodes/ultraspeed half print.gcode, print time was 0h 20m m122 === Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.6.0-alpha.2+3 (2024-07-17 20:03:21) running on Duet WiFi 1.02 or later Board ID: 0JD2M-9F8TA-GJ4TD-6J1D6-3SD6P-16PG6 Used output buffers: 3 of 26 (23 max) === RTOS === Static ram: 23368 Dynamic ram: 68644 of which 0 recycled Never used RAM 3768, free system stack 102 words Tasks: NETWORK(1,ready,25.0%,195) HEAT(3,nWait 5,0.1%,309) Move(4,nWait 5,5.1%,272) MAIN(1,running,69.8%,714) IDLE(0,ready,0.1%,29), total 100.0% Owned mutexes: WiFi(NETWORK) USB(MAIN) === Platform === Last reset 00:49:37 ago, cause: software Last software reset at 2024-07-19 19:46, reason: User, Gcodes spinning, available RAM 13680, slot 2 Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a Error status: 0x00 Aux0 errors 0,0,0 MCU temperature: min 29.4, current 29.9, max 31.2 Supply voltage: min 24.5, current 25.0, max 25.4, under voltage events: 1, over voltage events: 0, power good: yes Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/336/336, gc cycles 0 Events: 0 queued, 0 completed Date/time: 2024-07-19 20:35:52 Slowest loop: 248.15ms; fastest: 0.13ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Storage === Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest read time 14.6ms, write time 1.7ms, max retries 0 === Move === Segments created 929, maxWait 340401ms, bed comp in use: mesh, height map offset 0.000, hiccups added 56 (1.67ms), max steps late 1, ebfmin 0.00, ebfmax 0.00, mcet 0.058 Pos req/act/dcf: 29200.00/29199/1.00 -28400.00/-28400/-0.01 320240.00/320240/0.02 no step interrupt scheduled === DDARing 0 === Scheduled moves 77865, completed 77865, LaErrors 0, Underruns [54, 0, 0] Driver 0: standstill, SG min 0 Driver 1: standstill, SG min 0 Driver 2: standstill, SG min 0 Driver 3: standstill, SG min 0 Driver 4: standstill, SG min 0 Driver 5: Driver 6: Driver 7: Driver 8: Driver 9: Driver 10: Driver 11: === Heat === Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0 Heater 0 is on, I-accum = 0.2 === GCodes === Movement locks held by null HTTP is idle in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is ready with "m122" in state(s) 0 Aux is idle in state(s) 0 Trigger is idle in state(s) 0 Queue is idle in state(s) 0 LCD is idle in state(s) 0 Daemon is idle in state(s) 0 Autopause is idle in state(s) 0 Q0 segments left 0 Code queue 0 is empty === Network === Slowest loop: 222.56ms; fastest: 0.07ms Responder states: HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) HTTP sessions: 2 of 8 === WiFi === Interface state: active Module is connected to access point Failed messages: pending 0, notrdy 0, noresp 0 Firmware version 2.1.0 MAC address a4:e5:7c:03:da:81 Module reset reason: Power up, Vcc 3.42, flash size 2097152, free heap 42752 WiFi IP address 192.168.1.197 Signal strength -45dBm, channel 11, mode 802.11n, reconnections 0 Clock register 00002002 Socket states: 0 0 0 0 0 0 0 0 ok