M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.5.2 (2024-06-11 17:13:58) running on Duet 3 MB6HC v1.01 (SBC mode)
Board ID: 08DJM-9P63L-DJ3T8-6J1F0-3SN6P-TU7ZA
Used output buffers: 1 of 40 (19 max)
=== RTOS ===
Static ram: 155360
Dynamic ram: 90452 of which 0 recycled
Never used RAM 96796, free system stack 148 words
Tasks: SBC(2,ready,0.9%,821) HEAT(3,nWait 6,0.0%,321) Move(4,nWait 6,1.9%,211) CanReceiv(6,nWait 1,0.0%,796) CanSender(5,nWait 7,0.0%,329) CanClock(7,delaying,0.0%,346) TMC(4,nWait 6,9.9%,53) MAIN(2,running,87.1%,101) IDLE(0,ready,0.0%,29), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 01:25:34 ago, cause: software
Last software reset at 2024-07-15 10:23, reason: User, Platform spinning, available RAM 99916, slot 2
Software reset code 0x6000 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
MCU temperature: min 40.0, current 43.6, max 44.3
Supply voltage: min 23.9, current 24.0, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.2, current 12.2, max 12.3, under voltage events: 0
Heap OK, handles allocated/used 99/3, heap memory allocated/used/recyclable 2048/64/8, gc cycles 0
Events: 1 queued, 1 completed
Driver 0: ok, SG min 0, mspos 533, reads 38623, writes 17 timeouts 0
Driver 1: ok, SG min 0, mspos 990, reads 38623, writes 17 timeouts 0
Driver 2: ok, SG min 0, mspos 426, reads 38624, writes 17 timeouts 0
Driver 3: standstill, SG min 0, mspos 472, reads 38624, writes 17 timeouts 0
Driver 4: ok, SG min 0, mspos 250, reads 38624, writes 17 timeouts 0
Driver 5: standstill, SG min 0, mspos 952, reads 38624, writes 17 timeouts 0
Date/time: 2024-07-15 11:48:52
Slowest loop: 673.05ms; fastest: 0.05ms
=== Storage ===
Free file entries: 20
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 22, maxWait 254862ms, bed compensation in use: mesh, height map offset 0.000, max steps late 0, min interval 0, bad calcs 0, ebfmin 0.00, ebfmax 1.00
next step interrupt due in 145 ticks, disabled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 54100, completed 54072, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state 3
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 0 is on, I-accum = 0.5
Heater 1 is on, I-accum = 0.4
=== GCodes ===
Movement locks held by null, null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is idle in state(s) 3
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 2, axes/extruders owned 0x48000007
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== CAN ===
Messages queued 95108, received 41089, lost 0, errs 0, boc 0
Longest wait 1ms for reply type 6018, peak Tx sync delay 510, free buffers 50 (min 49), ts 25675/25674/0
Tx timeouts 0,0,0,0,0,0
=== SBC interface ===
Transfer state: 5, failed transfers: 0, checksum errors: 0
RX/TX seq numbers: 6252/6252
SPI underruns 0, overruns 0
State: 5, disconnects: 0, timeouts: 0 total, 0 by SBC, IAP RAM available 0x24cfc
Buffer RX/TX: 3936/1360-4080, open files: 0
=== Duet Control Server ===
Duet Control Server version 3.5.2 (2024-06-12 07:09:26, 32-bit)
HTTP+Executed:
> Executing M122
File 0:/gcodes/Freeze_Pipe_Joint_Adapter.gcode is selected, processing
File:
Buffered code: G1 X124.123 Y132.462 E1.64167
Buffered code: G1 X121.860 Y132.462 E0.09031
Buffered code: G1 X95.038 Y105.640 E1.51395
Buffered code: G1 X95.038 Y107.903 E0.09031
Buffered code: G1 X119.597 Y132.462 E1.38623
Buffered code: G1 X117.335 Y132.462 E0.09031
Buffered code: G1 X95.038 Y110.165 E1.25851
Buffered code: G1 X95.038 Y112.428 E0.09031
Buffered code: G1 X115.072 Y132.462 E1.13080
Buffered code: G1 X112.809 Y132.462 E0.09031
Buffered code: G1 X95.038 Y114.691 E1.00308
Buffered code: G1 X95.038 Y116.954 E0.09031
Buffered code: G1 X110.546 Y132.462 E0.87536
Buffered code: G1 X108.284 Y132.462 E0.09031
Buffered code: G1 X95.038 Y119.216 E0.74764
Buffered code: G1 X95.038 Y121.479 E0.09031
Buffered code: G1 X106.021 Y132.462 E0.61992
Buffered code: G1 X103.758 Y132.462 E0.09031
Buffered code: G1 X95.038 Y123.742 E0.49220
Buffered code: G1 X95.038 Y124.933 E0.04753
Buffered code: G1 X95.141 Y126.107 E0.04706
Buffered code: G1 X101.393 Y132.359 E0.35288
Buffered code: G1 E-7.00000 F4000
Buffered code: ; layer 83, Z = 16.5800
Buffered code: G1 X94.750 Y95.055 F6000
Buffered code: G1 Z16.5800 F2000
Buffered code: G1 E7.00000 F4000
Buffered code: G1 X94.872 Y93.655 E0.05607 F1920
Buffered code: G1 X95.222 Y92.351 E0.05388
Buffered code: G1 X95.792 Y91.127 E0.05389
Buffered code: G1 X96.382 Y90.285 E0.04105
Buffered codes: 1480 bytes total
Code buffer space: 2576
Configured SPI speed: 8000000Hz, TfrRdy pin glitches: 0
Full transfers per second: 39.56, max time between full transfers: 133.4ms, max pin wait times: 58.5ms/10.7ms
Codes per second: 8.91
Maximum length of RX/TX data transfers: 4822/1664