6/30/2024, 10:31:46 AM	M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.5.2 (2024-06-11 17:13:43) running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DGM-9T6BU-FG3SD-6J1D0-3SD6R-1UMVF
Used output buffers: 17 of 26 (19 max)
Error in macro line 16 while starting up: Accelerometer not found on specified port
=== RTOS ===
Static ram: 23384
Dynamic ram: 78060 of which 12 recycled
Never used RAM 7776, free system stack 104 words
Tasks: NETWORK(2,nWait 6,16.1%,202) HEAT(3,nWait 5,0.1%,307) Move(4,nWait 5,1.4%,258) DUEX(5,nWait 5,0.0%,23) MAIN(1,running,81.3%,713) IDLE(0,ready,1.2%,29), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 65:35:15 ago, cause: power up
Last software reset at 2024-06-25 10:17, reason: User, Gcodes spinning, available RAM 10384, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x08
Aux0 errors 0,0,0
MCU temperature: min 21.8, current 31.1, max 32.7
Supply voltage: min 23.6, current 24.0, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/2, heap memory allocated/used/recyclable 2048/228/176, gc cycles 0
Events: 5913526 queued, 5913526 completed
Driver 0: standstill, SG min n/a
Driver 1: standstill, SG min 0
Driver 2: standstill, SG min 0
Driver 3: standstill, SG min 0
Driver 4: standstill, SG min 0
Driver 5: standstill, SG min 0
Driver 6: standstill, SG min 0
Driver 7: standstill, SG min 0
Driver 8: standstill, SG min 0
Driver 9: standstill, SG min 0
Driver 10: 
Driver 11: 
Date/time: 2024-06-30 10:31:30
Cache data hit count 4294967295
Slowest loop: 248.92ms; fastest: 0.12ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 37.1ms, write time 8.9ms, max retries 0
=== Move ===
DMs created 83, segments created 44, maxWait 66318838ms, bed compensation in use: mesh, height map offset 0.000, max steps late 1, min interval 0, bad calcs 0, ebfmin -0.00, ebfmax 1.00
no step interrupt scheduled
Moves shaped first try 133206, on retry 25040, too short 268131, wrong shape 434716, maybepossible 36903
=== DDARing 0 ===
Scheduled moves 1203320, completed 1203320, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 49], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Movement locks held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Q0 segments left 0
Code queue 0 is empty
=== DueX ===
Read count 1, 0.00 reads/min
=== Network ===
Slowest loop: 203.40ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8
=== WiFi ===
Interface state: active
Module is connected to access point 
Failed messages: pending 0, notrdy 0, noresp 0
Firmware version 2.1.0
MAC address a0:20:a6:32:50:95
Module reset reason: Turned on by main processor, Vcc 3.39, flash size 4194304, free heap 36432
WiFi IP address 192.168.68.119
Signal strength -43dBm, channel 5, mode 802.11n, reconnections 0
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0