9:21:14 AM: M122: === Diagnostics ===RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later + DueX5Board ID: 08DLM-996AL-K65SW-6J1F0-3SJ6P-9V5LXUsed output buffers: 1 of 24 (14 max)=== RTOS ===Static ram: 25712Dynamic ram: 93544 of which 520 recycledException stack ram used: 312Never used ram: 10984Tasks: NETWORK(ready,628) HEAT(blocked,1232) DUEX(suspended,160) MAIN(running,3648) IDLE(ready,160)Owned mutexes:=== Platform ===Last reset 00:06:33 ago, cause: softwareLast software reset at 2023-08-17 09:14, reason: User, spinning module GCodes, available RAM 10800 bytes (slot 3)Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414dError status: 0Free file entries: 10SD card 0 detected, interface speed: 20.0MBytes/secSD card longest block write time: 0.0ms, max retries 0MCU temperature: min 21.1, current 21.3, max 21.8Supply voltage: min 24.3, current 24.5, max 24.7, under voltage events: 0, over voltage events: 0, power good: yesDriver 0: standstill, SG min/max not availableDriver 1: standstill, SG min/max not availableDriver 2: standstill, SG min/max not availableDriver 3: standstill, SG min/max not availableDriver 4: standstill, SG min/max not availableDriver 5: standstill, SG min/max not availableDriver 6: standstill, SG min/max not availableDriver 7: standstill, SG min/max not availableDriver 8: standstill, SG min/max not availableDriver 9: standstill, SG min/max not availableDate/time: 2023-08-17 09:21:13Cache data hit count 1201667275Slowest loop: 33.67ms; fastest: 0.07msI2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0=== Move ===Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0msBed compensation in use: none, comp offset 0.000=== DDARing ===Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0=== Heat ===Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1=== GCodes ===Segments left: 0Stack records: 1 allocated, 0 in useMovement lock held by nullhttp is idle in state(s) 0telnet is idle in state(s) 0file is idle in state(s) 0serial is idle in state(s) 0aux is idle in state(s) 0daemon is idle in state(s) 0queue is idle in state(s) 0autopause is idle in state(s) 0Code queue is empty.=== Network ===Slowest loop: 36.26ms; fastest: 0.00msResponder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)HTTP sessions: 1 of 8- WiFi -Network state is runningWiFi module is providing access point Failed messages: pending 0, notready 0, noresp 0WiFi firmware version 1.23WiFi MAC address 4a:3f:da:88:cc:b8WiFi Vcc 3.34, reset reason Turned on by main processorWiFi flash size 4194304, free heap 24840WiFi IP address 11.22.33.44Connected clients 1Socket states: 0 0 0 0 0 0 0 0
9:19:42 AM: M588 S""Z1026""
9:19:35 AM: M588""Z1026"": Error: M588: Bad or missing parameter
9:19:13 AM: M552: WiFi module is providing access point Z1026, IP address 11.22.33.44
9:18:54 AM: M587: Remembered networks:TNCAPF2FD81 IP=192.168.1.14 GW=0.0.0.0 NM=0.0.0.0Z1026 IP=11.22.33.44 GW=0.0.0.0 NM=0.0.0.0
9:18:49 AM: Connection established!
9:18:49 AM: Page Load complete!