9/20/2022, 5:41:18 PM: M122 : === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.4.0 (2022-03-15 18:57:24) running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956BA-NA3TJ-6JTDL-3S06T-9T86T
Used output buffers: 1 of 40 (21 max)
=== RTOS ===
Static ram: 151000
Dynamic ram: 69108 of which 0 recycled
Never used RAM 129820, free system stack 114 words
Tasks: SBC(ready,0.7%,436) HEAT(notifyWait,0.0%,321) Move(notifyWait,0.0%,210) CanReceiv(notifyWait,0.0%,772) CanSender(notifyWait,0.0%,346) CanClock(delaying,0.0%,339) TMC(notifyWait,8.0%,58) MAIN(running,91.3%,923) IDLE(ready,0.0%,30), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 28:03:46 ago, cause: software
Last software reset at 2022-09-19 13:37, reason: User, GCodes spinning, available RAM 129496, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 134
MCU temperature: min 42.9, current 43.1, max 43.3
Supply voltage: min 23.8, current 23.9, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a, mspos 472, reads 47855, writes 0 timeouts 0
Driver 1: standstill, SG min n/a, mspos 376, reads 47855, writes 0 timeouts 0
Driver 2: standstill, SG min n/a, mspos 584, reads 47855, writes 0 timeouts 0
Driver 3: standstill, SG min n/a, mspos 904, reads 47855, writes 0 timeouts 0
Driver 4: standstill, SG min n/a, mspos 328, reads 47854, writes 0 timeouts 0
Driver 5: standstill, SG min n/a, mspos 152, reads 47855, writes 0 timeouts 0
Date/time: 2022-09-20 17:41:18
Slowest loop: 21.94ms; fastest: 0.04ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 31, maxWait 0ms, bed compensation in use: mesh, comp offset 0.147
=== MainDDARing ===
Scheduled moves 279029, completed 279029, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is idle in state(s) 0
USB is idle in state(s) 0
Aux is assembling a command in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== CAN ===
Messages queued 1673, received 8912, lost 0, boc 0
Longest wait 2ms for reply type 6024, peak Tx sync delay 6, free buffers 50 (min 49), ts 925/925/0
Tx timeouts 0,0,0,0,0,0
=== SBC interface ===
Transfer state: 4, failed transfers: 0, checksum errors: 0
RX/TX seq numbers: 14345/14345
SPI underruns 0, overruns 0
State: 5, disconnects: 2, timeouts: 2, IAP RAM available 0x2b880
Buffer RX/TX: 0/0-0, open files: 0
=== Duet Control Server ===
Duet Control Server v3.4.0
Code buffer space: 4096
Configured SPI speed: 8000000Hz, TfrRdy pin glitches: 11
Full transfers per second: 39.11, max time between full transfers: 47.5ms, max pin wait times: 48.8ms/6.7ms
Codes per second: 0.01
Maximum length of RX/TX data transfers: 5328/1572