08/07/2022, 16:18:42: M122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.4.1 (2022-06-01 21:09:01) running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-9P63L-DJ3T8-6J9D8-3SD6R-TV439
Used output buffers: 1 of 40 (12 max)
=== RTOS ===
Static ram: 151000
Dynamic ram: 66164 of which 204 recycled
Never used RAM 129464, free system stack 129 words
Tasks: SBC(ready,7.9%,466) HEAT(notifyWait,0.3%,321) Move(notifyWait,64.1%,248) CanReceiv(notifyWait,0.0%,944) CanSender(notifyWait,0.0%,356) CanClock(delaying,0.1%,333) TMC(notifyWait,106.2%,58) MAIN(running,339.0%,923) IDLE(ready,0.5%,30), total 518.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 05:09:09 ago, cause: software
Last software reset at 2022-06-08 19:21, reason: User, GCodes spinning, available RAM 129272, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
Step timer max interval 152
MCU temperature: min 36.0, current 40.8, max 41.2
Supply voltage: min 23.9, current 24.0, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.2, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/1078/1078, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 0, mspos 456, reads 63560, writes 64 timeouts 0
Driver 1: standstill, SG min 0, mspos 600, reads 63560, writes 64 timeouts 0
Driver 2: standstill, SG min 0, mspos 696, reads 63560, writes 64 timeouts 0
Driver 3: standstill, SG min 0, mspos 56, reads 63560, writes 64 timeouts 0
Driver 4: standstill, SG min 0, mspos 744, reads 63560, writes 64 timeouts 0
Driver 5: standstill, SG min 0, mspos 152, reads 63604, writes 20 timeouts 0
Date/time: 2022-06-09 00:30:44
Slowest loop: 385.83ms; fastest: 0.03ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 41, maxWait 5194498ms, bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves 1405167, completed 1405167, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 27], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 0 is on, I-accum = 0.3
Heater 1 is on, I-accum = 0.6
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is doing "G4 S120" in state(s) 0 37, running macro
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== CAN ===
Messages queued 166938, received 0, lost 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 50 (min 50), ts 92749/0/0
Tx timeouts 0,0,92748,0,0,74188 last cancelled message type 4514 dest 127
=== SBC interface ===
Transfer state: 5, failed transfers: 0, checksum errors: 0
RX/TX seq numbers: 3528/3528
SPI underruns 0, overruns 0
State: 5, disconnects: 0, timeouts: 0 total, 0 by SBC, IAP RAM available 0x2b880
Buffer RX/TX: 360/512-0, open files: 0
=== Duet Control Server ===
Duet Control Server v3.4.1
File /opt/dsf/sd/gcodes/01_PEETER/Rev_2x/01_SensorCap/drrxx_PETG_015mmF_R4_Cap_PEETER.gcode is selected, processing
File:
Buffered code: G4 S120 ; Wait 2 minutes
Buffered code: M290 R0 S0 ; clear babystepping
Buffered code: M106 P1 S0 ; Fan off
Buffered code: M84 ; Steppers off
Buffered code: M400 ; Clear queue
==> 160 bytes
Executing macro stop.g, started by M0 ;stop.g
Number of flush requests: 1
> Next stack level
Code buffer space: 3584
Configured SPI speed: 8000000Hz, TfrRdy pin glitches: 0
Full transfers per second: 39.06, max time between full transfers: 111.2ms, max pin wait times: 62.7ms/12.7ms
Codes per second: 3.80
Maximum length of RX/TX data transfers: 3196/1600