M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956L2-G43S8-6J1D6-3S86R-KA3YF
Used output buffers: 1 of 40 (11 max)
=== RTOS ===
Static ram: 150904
Dynamic ram: 62236 of which 28 recycled
Never used RAM 138168, free system stack 127 words
Tasks: SBC(ready,4.7%,328) HEAT(delaying,0.0%,325) Move(notifyWait,0.2%,250) CanReceiv(notifyWait,0.0%,774) CanSender(notifyWait,0.0%,366) CanClock(delaying,0.0%,339) TMC(notifyWait,8.3%,59) MAIN(running,86.7%,922) IDLE(ready,0.0%,29), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 01:02:17 ago, cause: power up
Last software reset at 2022-05-30 16:52, reason: User, none spinning, available RAM 138136, slot 2
Software reset code 0x0012 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0440f000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
Step timer max interval 170
MCU temperature: min 15.6, current 39.1, max 39.2
Supply voltage: min 23.7, current 23.9, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 11.8, current 11.9, max 12.0, under voltage events: 0
Heap OK, handles allocated/used 99/1, heap memory allocated/used/recyclable 2048/418/392, gc cycles 0
Driver 0: position 32310, ok, reads 64666, writes 25 timeouts 0, SG min/max 0/1023
Driver 1: position 1753, ok, reads 64666, writes 25 timeouts 0, SG min/max 0/1023
Driver 2: position 56242, ok, reads 64666, writes 25 timeouts 0, SG min/max 0/1023
Driver 3: position 0, ok, reads 64667, writes 25 timeouts 0, SG min/max 0/1023
Driver 4: position 0, ok, reads 64667, writes 25 timeouts 0, SG min/max 0/1023
Driver 5: position 0, standstill, reads 64681, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2022-06-14 10:13:57
Slowest loop: 162.29ms; fastest: 0.03ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 238258ms, bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves 72727, completed moves 72669, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 8], CDDA state 3
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is doing "G1 X171.703003 Y164.852005 E0.017680" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 102629, received 47591, lost 0, longest wait 2ms for reply type 6031, peak Tx sync delay 18546, free buffers 49 (min 43), ts 18688/18687/0
Tx timeouts 0,0,0,0,0,0
=== SBC interface ===
State: 4, failed transfers: 1, checksum errors: 0
Last transfer: 1ms ago
RX/TX seq numbers: 42728/42915
SPI underruns 0, overruns 0
Disconnects: 1, timeouts: 0, IAP RAM available 0x2c83c
Buffer RX/TX: 1544/2960-0
=== Duet Control Server ===
Duet Control Server v3.3.0
File:
Buffered code: G1 X172.134 Y163.241 E0.13
Buffered code: G1 X172.42 Y161.428 E0.14308
Buffered code: G1 X172.512 Y159.673 E0.137
Buffered code: G1 X172.508 Y159.432 E0.01879
Buffered code: G1 X172.419 Y157.771 E0.12967
Buffered code: G1 X172.134 Y155.958 E0.14307
Buffered code: G1 X171.662 Y154.201 E0.14182
Buffered code: G1 X171.002 Y152.476 E0.14398
Buffered code: G1 X170.167 Y150.842 E0.14304
Buffered code: G1 X169.171 Y149.306 E0.14271
Buffered code: G1 X168.014 Y147.88 E0.14315
Buffered code: G1 X166.719 Y146.583 E0.14287
Buffered code: G1 X165.295 Y145.429 E0.14288
Buffered code: G1 X163.758 Y144.433 E0.14277
Buffered code: G1 X162.123 Y143.598 E0.14311
Buffered code: G1 X160.399 Y142.936 E0.14396
Buffered code: G1 X158.641 Y142.466 E0.14186
Buffered code: G1 X156.828 Y142.18 E0.14308
Buffered code: G1 X155.001 Y142.084 E0.14262
Buffered code: G1 X153.173 Y142.181 E0.1427
Buffered code: G1 X151.36 Y142.466 E0.14307
Buffered code: G1 X149.601 Y142.938 E0.14197
Buffered code: G1 X147.876 Y143.598 E0.14398
Buffered code: G1 X146.242 Y144.433 E0.14304
Buffered code: G1 X144.706 Y145.429 E0.14271
Buffered code: G1 X143.279 Y146.585 E0.14316
Buffered code: G1 X141.983 Y147.881 E0.14287
Buffered code: G1 X140.829 Y149.305 E0.14288
Buffered code: G1 X139.831 Y150.844 E0.14299
Buffered code: G1 X138.998 Y152.476 E0.14283
Buffered code: G1 X138.363 Y154.131 E0.13818
==> 1488 bytes
Pending code: G1 X138.297 Y154.348 E0.01768
Code buffer space: 1496
Configured SPI speed: 8000000Hz
Full transfers per second: 2.70, max wait times: 14.9ms/0.0ms
Codes per second: 1.15
Maximum length of RX/TX data transfers: 3088/1600
File /opt/dsf/sd/gcodes/TM_BA_Bottle_Belt_Clip_035-PETG.gcode is selected, processing