4/25/2022, 12:29:47 PM: Connected to 192.168.1.158
4/25/2022, 12:30:49 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956BA-NA3TJ-6JTDL-3S06T-9T86T
Used output buffers: 1 of 40 (16 max)
=== RTOS ===
Static ram: 150904
Dynamic ram: 63700 of which 0 recycled
Never used RAM 139588, free system stack 202 words
Tasks: SBC(ready,16.4%,338) HEAT(delaying,0.0%,325) Move(notifyWait,0.0%,352) CanReceiv(notifyWait,0.0%,908) CanSender(notifyWait,0.0%,374) CanClock(delaying,0.0%,339) TMC(notifyWait,7.2%,93) MAIN(running,74.7%,922) IDLE(ready,1.7%,29), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:04:27 ago, cause: power up
Last software reset at 2022-04-24 17:32, reason: User, none spinning, available RAM 136484, slot 0
Software reset code 0x0012 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,1
Step timer max interval 129
MCU temperature: min 14.7, current 29.4, max 29.5
Supply voltage: min 23.8, current 23.9, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, reads 52327, writes 14 timeouts 0, SG min/max 0/0
Driver 1: position 0, standstill, reads 52327, writes 14 timeouts 0, SG min/max 0/0
Driver 2: position 0, standstill, reads 52327, writes 14 timeouts 0, SG min/max 0/0
Driver 3: position 0, standstill, reads 52327, writes 14 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 52327, writes 14 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 52327, writes 14 timeouts 0, SG min/max 0/0
Date/time: 2022-04-25 12:30:49
Slowest loop: 0.45ms; fastest: 0.04ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is assembling a command in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 2330, received 30, lost 0, longest wait 1ms for reply type 6018, peak Tx sync delay 7, free buffers 49 (min 48), ts 1338/1337/0
Tx timeouts 0,0,0,0,0,0
=== SBC interface ===
State: 4, failed transfers: 1, checksum errors: 0
Last transfer: 2ms ago
RX/TX seq numbers: 42100/42100
SPI underruns 0, overruns 0
Disconnects: 0, timeouts: 0, IAP RAM available 0x2c83c
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.4.0
Code buffer space: 4096
Configured SPI speed: 8000000Hz, TfrRdy pin glitches: 2
Full transfers per second: 13.69, max time between full transfers: 29.5ms, max pin wait times: 24.6ms/15.9ms
Codes per second: 0.00
Maximum length of RX/TX data transfers: 4089/656