; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Sat Dec 08 2018 14:23:46 GMT+0200 (Itä-Euroopan normaaliaika)

; General preferences
G90                                                ; Send absolute coordinates...
M83                                                ; ...but relative extruder moves

; Network
M550 P"xxx"                                   ; Set machine name
M551 P"xxxx:                                    ; Set password
M552 S1                                            ; Enable network
;*** Access point is configured manually via M587
M586 P0 S1                                         ; Enable HTTP
M586 P1 S0                                         ; Disable FTP
M586 P2 S0                                         ; Disable Telnet

; Drives
M569 P0 S1                                         ; Drive 0 goes forwards
M569 P1 S1                                         ; Drive 1 goes forwards
M569 P2 S1                                         ; Drive 2 goes backwards
M569 P3 S0                                         ; Drive 3 goes forwards
M350 X16 Y16 Z16 E16 I1                            ; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z1600.00 E836.00                 ; Set steps per mm
M566 X600.00 Y600.00 Z12.00 E120.00                ; Set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z240.00 E9200.00            ; Set maximum speeds (mm/min)
M201 X700.00 Y700.00 Z50.00 E500.00                ; Set accelerations (mm/s^2)
M906 X950.00 Y950.00 Z1000.00 E950.00 I25          ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; Set axis minima
M208 X196 Y190 Z100 S0                             ; Set axis maxima

; Endstops
M574 X1 Y1 S0                                      ; Set active low endstops
M581 E0 S0 T0 C0 ;			           ; Hardwired Stop -button

; Z-Probe
M574 Z1 S2                                         ; Set endstops controlled by probe
M558 P5 F80 T6000 H5 A2                             ; Set Z probe type to switch and the dive height + speeds
G31 P500 X0 Y40 Z1.943                                 ; Set Z probe trigger value, offset and trigger height1.380   1liian kaukana, 3 osuu petiin. 1.143oli....
M557 X0:180 Y40:140 S20                           ; Define mesh grid

; Heaters
M307 H0 B0 S1.00                                   ; Disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B3974 R4700                        ; Set thermistor + ADC parameters for heater 0
M143 H0 S120                                       ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4388 C7.060000e-8 R4700           ; Set thermistor + ADC parameters for heater 1
M143 H1 S280                                       ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0.0 I0 F100 L0.2 X1.0 H-1                      ; (part cooling)Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 X1.0 H1 T45 C"HOTEND_FAN"                         ; (hotend cooling) Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S0.2 F2500 C"DUET_FAN"                    			; (duet cooling) Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1                                      ; Define tool 0
G10 P0 X0 Y0 Z0                                    ; Set tool 0 axis offsets
G10 P0 R0 S0                                       ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
; M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured