Config.g: ``` ;Modix Big-60 V2-V3, single printhead ;Written by Elad E. ; General preferences_______________________________________________ G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves M111 S0 ; Debug off M555 P2 ; Set output to look like Marlin M575 P1 B57600 S1 ; Set auxiliary serial port baud rate and require checksum (for PanelDue) ; Network___________________________________________________________ M550 P"Big-60 V2-V3" ; Set machine name ;M551 P"MODIX3D" ; Set password (optional) M552 S1 ; Enable network M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; Drives ;Main board_________________________________________________________ M569 P0 S1 ; Physical drive 0 goes forwards. X-Axis. M569 P1 S0 ; Physical drive 1 goes backwards. Y-Axis. M569 P2 S0 ; Physical drive 2 goes backwards. Z-Axis. M569 P3 S1 ; Physical drive 3 goes forwards. E0-Extruder. M569 P4 R-1 ; Physical drive 4 goes backwards. E1-Extruder. ;___________________________________________________________________ M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation M92 X200.00 Y100.00 Z2000.00 E418.500 ; Set steps per mm M566 X240 Y360 Z30.00 E120.00 P1 ; Set maximum instantaneous speed changes (mm/min) M203 X6000.00 Y6000.00 Z360.00 E1200.00 ; Set maximum speeds (mm/min) M201 X1000.00 Y1000.00 Z120.00 E250.00 ; Set accelerations (mm/s^2) M204 P500 T1000 ; Set print and travel accelerations (mm/s^2) M906 X1800.00 Y1800.00 Z2400.00 E1000.00 I40 ; Set motor currents (mA) and motor idle factor in per cent M84 S60 X Y E0 ; Set idle timeout - one minute ; Axis Limits_______________________________________________________ M208 X0 Y0 Z0 S1 ; set axis minima M208 X610 Y610 Z610 S0 ; Set axis maxima ; Endstops__________________________________________________________ M574 X2 S0 P"!xstop" ; configure active-high endstop for low end on X via pin xstop M574 Y2 S0 P"!ystop" ; configure active-high endstop for high end on Y via pin ystop ; Z-Probe___________________________________________________________ M574 Z0 ; Configure Z-probe endstop on Z M307 H7 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch M558 P9 X0 Y0 Z1 H5 F120 T6000 ; Set Z probe type to bltouch and the dive height + speed ;G31 P50 X-25 Y38 Z1.5 ; Set Z probe trigger value, offset and trigger height G31 X-25 Y38 Z1.5 ; Set Z probe trigger value (without P50), offset and trigger height M557 X-30:568.5 Y21:606 S66.5:65 ; Define mesh grid. 100 Points M376 H10 ; Height (mm) over which to taper off the bed compensation ; Heaters___________________________________________________________ M140 H-1 ; Disable heated bed M307 H0 A-1 C-1 D-1 ; Disable heater on PWM channel ;E0_________________________________________________________________ M305 P1 T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 1 M143 H1 S285 ; Set temperature limit for heater 1 to 285C ;M307 H1 A# C# D# V# S1.0 B0 ; PID calibration ; Fans______________________________________________________________ M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P1 I-1 ; Disable fan channel for LED M106 P2 I-1 ; Disable fan channel for LED ; Tools ;T0_________________________________________________________________ M563 P0 S"E0 Primary" D0 H1 F0 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S210 ; Set initial tool 0 active and standby temperatures to 0C ; Automatic power saving____________________________________________ M911 S22.5 R29.0 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss. Power Failure Pause ; Custom settings___________________________________________________ M591 D0 P1 C3 S1 ; Regular filament sensor for E0 M564 H0 S0 ; Negative movements are allowed ``` Homeall.g: ``` ; called to home all axes M280 P7 S60 I1 G91 ; relative positioning G1 H2 Z5 F1000 ; lift Z relative to current position G1 H1 X-610 Y-610 F4000 ; move quickly to X and Y axis endstops and stop there (first pass) G1 H2 X10 F1000 ; X back a few mm G1 H2 Y10 F1000 ; Y back a few mm G1 H1 X-610 Y-610 F1000 ; move slowly to X and Y axis endstops once more (second pass) G1 H2 X40 F1000 ; X back a few mm G1 H2 Y40 F1000 ; Y back a few mm G90 ; absolute positioning G30 ; home Z by probing the bed G92 X0 Y0 ``` Homex.g: ``` ; homex.g ; called to home the X axis G91 ; relative positioning G1 H2 Z5 F200 ; lift Z relative to current position G1 H1 X-610 F3000 ; move quickly to X axis endstop and stop there (first pass) G1 H2 X50 F1000 ; go back a few mm G1 H1 X-610 F1000 ; move slowly to X axis endstop once more (second pass) G1 H2 X50 F1000 ; go back a few mm G1 H2 Z5 F3000 ; lower Z again G90 ; absolute positioning ``` Homey.g: ``` ; homey.g ; called to home the Y axis G91 ; relative positioning G1 H2 Z5 F200 ; lower Z relative to current position G1 H1 Y-610 F3000 ; move quickly to Y axis endstop and stop there (first pass) G1 H2 Y50 F1000 ; go back a few mm G1 H1 Y-610 F1000 ; move slowly to Y axis endstop once more (second pass) G1 H2 Y50 F1000 ; go back a few mm G1 H2 Z5 F3000 ; lower Z again G90 ; absolute positioning ``` Homez.g: ``` ; homez.g ; called to home the Z axis M280 P7 S90 I1 G91 ; relative positioning G1 H2 Z5 F200 ; lift Z relative to current position G90 ; absolute positioning M401 ; Lower Z probe (BLTouch) G30 ; home Z by probing the bed M402 ; Retract Probe ;M375 ; Loads the grid matrix file (Heightmap) ``` === Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later Board ID: 08DGM-956GU-DJ3S0-7JKDG-3SJ6Q-TAGVF Used output buffers: 2 of 24 (16 max) === RTOS === Static ram: 25712 Dynamic ram: 93220 of which 0 recycled Exception stack ram used: 440 Never used ram: 11700 Tasks: NETWORK(ready,764) HEAT(blocked,1232) MAIN(running,3808) IDLE(ready,160) Owned mutexes: === Platform === Last reset 00:29:04 ago, cause: software Last software reset at 2021-08-23 11:45, reason: User, spinning module GCodes, available RAM 11904 bytes (slot 2) Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d Error status: 0 Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest block write time: 0.0ms, max retries 0 MCU temperature: min 33.7, current 34.1, max 34.4 Supply voltage: min 24.2, current 24.4, max 24.7, under voltage events: 0, over voltage events: 0, power good: yes Driver 0: standstill, SG min/max not available Driver 1: standstill, SG min/max not available Driver 2: standstill, SG min/max not available Driver 3: standstill, SG min/max not available Driver 4: standstill, SG min/max not available Date/time: 2021-08-23 12:14:56 Cache data hit count 4294967295 Slowest loop: 2.10ms; fastest: 0.07ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Move === Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms Bed compensation in use: none, comp offset 0.000 === DDARing === Scheduled moves: 10, completed moves: 10, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 === Heat === Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1 === GCodes === Segments left: 0 Stack records: 2 allocated, 0 in use Movement lock held by null http is ready with "M122 B121" in state(s) 0 telnet is idle in state(s) 0 file is idle in state(s) 0 serial is idle in state(s) 0 aux is idle in state(s) 0 daemon is idle in state(s) 0 queue is idle in state(s) 0 autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 201.16ms; fastest: 0.07ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0) HTTP sessions: 2 of 8 - WiFi - Network state is running WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 1 WiFi firmware version 1.26 WiFi MAC address f4:cf:a2:e3:29:c0 WiFi Vcc 3.32, reset reason Turned on by main processor WiFi flash size 4194304, free heap 26536 WiFi IP address 10.201.37.13 WiFi signal strength -47dBm, reconnections 0, sleep mode unknown Socket states: 0 0 0 0 0 0 0 0 === Filament sensors === Extruder 0 sensor: ok