0:/sys/config.g
; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.5 on Sat Jan 11 2020 15:38:33 GMT+0200 (Itä-Euroopan normaaliaika)

; General preferences
G90                                             ; send absolute coordinates...
M83                                             ; ...but relative extruder moves
M550 P"Leapfrog-Duet"                              ; set printer name

; Network
M552 S1                                         ; enable network
M586 P0 S1                                      ; enable HTTP
M586 P1 S0                                      ; disable FTP
M586 P2 S0                                      ; disable Telnet


; Drives
M569 P0 S0                                      ; physical drive 0 goes forwards
M569 P1 S1                                      ; physical drive 1 goes forwards
M569 P2 S1                                      ; physical drive 2 goes forwards
M569 P3 S1                                      ; physical drive 3 goes forwards
M569 P4 S1                                      ; physical drive 4 goes forwards
M569 P5 R0 T10:10:10:10 S0			; T10:10:10:10 T2.5:2.5:5:5
M584 X1 Y2 E3:4 Z5                           	; set drive mapping z TM 6600

M350 X16 Y16 Z16 E16:16 I1                      ; configure microstepping with interpolation
;M92 X66.67 Y66.67 Z640.20 E144.00:144.00 	; set steps per mm (direct drive)
M92 X66.67 Y66.67 Z640.20 E837.00:144.00 	; set steps per mm (titan aero)

M566 X900.00 Y900.00 Z60.00 E120.00:120.00      ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00:1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00:250.00      ; set accelerations (mm/s^2)

M906 X800 Y800 Z1600 E800:800 I30               ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                        	; Set idle timeout


; Axis Limits
M208 X0 Y0 Z0 S1                                ; set axis minima
M208 X210 Y250 Z200 S0                          ; set axis maxima

; Endstops
M574 Z0 S0                                      ; set active low and disabled endstops
M574 X1 Y1 S1                                   ; set active high endstops

; Z-Probe
M558 P0 H5 F120 T6000                           ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:200 Y15:195 S20                        ; define mesh grid

; Heaters
M305 P0 T100000 B4138 ;R4700                     ; set thermistor + ADC parameters for heater 0
M143 H0 S120                                    ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B3950 ;R4700                        ; set thermistor + ADC parameters for heater 1
M143 H1 S280                                    ; set temperature limit for heater 1 to 280C
M305 P2 T100000 B3950 ;R4700                   	; set thermistor + ADC parameters for heater 2
M143 H2 S280  					; set temperature limit for heater 2 to 280C
                                  

;In the M305 P1 and M305 P2 lines, change T100 to T100000 just as you have already in the M305 P0 line.
;You can remove the R4700 from all 3 M305 lines.





;M307 H1 A455.9 C183.2 D17.7 S1.00 V24.1 B0
;M307 H2 A499.7 C172.7 D10.4 S1.00 V24.1 B0
;M570 H1 P4 T20 s1
; Fans
M106 P0 S0 I0 F500 H-1                          ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H-1                          ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 S1 I0 F500 H-1                          ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0                                ; define tool 0
G10 P0 X0 Y0 Z0                                 ; set tool 0 axis offsets
G10 P0 R0 S0                                    ; set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H2 F0                                ; define tool 1
G10 P1 X0 Y0 Z0                                 ; set tool 1 axis offsets
G10 P1 R0 S0                                    ; set initial tool 1 active and standby temperatures to 0C

; Custom settings are not defined
Leapfrog-Duet
Send code...
Status
Idle
Tool Position
X
0.0
Y
0.0
Z
0.00
Extruder Drives
Drive 0
0.0
Drive 1
0.0
Speeds
Requested Speed
0 mm/s
Top Speed
0 mm/s
Sensors
Vin
24.1 V
MCU Temperature
32.6 C
Fan RPM
0
 Tools
 Extra
 Control All
Tool	Heater	Current	Active	Standby
Tool 0
T0 - Load Filament	Heater 1
off	21.8 C	
0
0
Tool 1
T1 - Load Filament	Heater 2
off	22.5 C	
0
0
Bed	Heater 0
off	21.9 C	
0
0
Temperature Chart
System Directory