m122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.3RC2 (2021-05-11 14:55:40) running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: J8ZB5-U296U-D65J0-40KML-NP03Z-H7HL5
Used output buffers: 3 of 40 (15 max)
=== RTOS ===
Static ram: 102476
Dynamic ram: 106368 of which 204 recycled
Never used RAM 34656, free system stack 128 words
Tasks: NETWORK(ready,15.2%,217) HEAT(delaying,0.0%,343) Move(notifyWait,0.1%,288) CanReceiv(notifyWait,0.0%,773) CanSender(notifyWait,0.0%,371) CanClock(delaying,0.0%,348) TMC(notifyWait,0.7%,115) MAIN(running,83.0%,426) IDLE(ready,0.2%,29) AIN(delaying,0.8%,273), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:02:29 ago, cause: software
Last software reset at 2021-05-24 19:43, reason: User, GCodes spinning, available RAM 34832, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Aux1 errors 0,0,0
MCU revision 3, ADC conversions started 149421, completed 149421, timed out 0, errs 0
Step timer max interval 1468
MCU temperature: min 26.7, current 28.2, max 28.5
Supply voltage: min 23.8, current 24.1, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 16000, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 95, reads 7837, writes 11, timeouts 0, DMA errors 0
Driver 1: position 16000, standstill, SG min/max 0/50, read errors 0, write errors 1, ifcnt 115, reads 7834, writes 14, timeouts 0, DMA errors 0
Driver 2: position 0, standstill, SG min/max 0/18, read errors 0, write errors 1, ifcnt 119, reads 7834, writes 14, timeouts 0, DMA errors 0
Driver 3: position 0, standstill, SG min/max 0/2, read errors 0, write errors 1, ifcnt 120, reads 7833, writes 14, timeouts 0, DMA errors 0
Driver 4: position 0, standstill, SG min/max 0/2, read errors 0, write errors 1, ifcnt 120, reads 7834, writes 14, timeouts 0, DMA errors 0
Driver 5: position 0, assumed not present
Driver 6: position 0, assumed not present
Date/time: 2021-05-24 19:45:50
Cache data hit count 281455062
Slowest loop: 5.41ms; fastest: 0.12ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 3.9ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 27462ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 6, completed moves 6, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by HTTP
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0 sensor: ok
=== CAN ===
Messages queued 1360, send timeouts 0, received 1865, lost 0, longest wait 2ms for reply type 6049, peak Tx sync delay 318, free buffers 17 (min 16)
=== Network ===
Slowest loop: 45.56ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 2 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.24beta2-05b1
WiFi MAC address f4:cf:a2:6f:be:16
WiFi Vcc 3.41, reset reason Power up
WiFi flash size 2097152, free heap 22680
WiFi IP address 192.168.1.219
WiFi signal strength -61dBm, mode none, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0