27/03/2021, 14:33:59	m122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.3beta2+1-swcrc running on Duet 3 Mini5plus WiFi (SBC mode)
Board ID: XJDX9-1296U-D65J0-40KMJ-4K03Z-7J6X6
Used output buffers: 1 of 40 (11 max)
=== RTOS ===
Static ram: 100008
Dynamic ram: 93480 of which 16 recycled
Never used RAM 50200, free system stack 126 words
Tasks: Linux(ready,145) HEAT(delaying,299) CanReceiv(notifyWait,943) CanSender(notifyWait,358) CanClock(delaying,340) TMC(notifyWait,109) MAIN(running,500) IDLE(ready,20) AIN(delaying,258)
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:35:30 ago, cause: software
Last software reset at 2021-03-27 08:58, reason: User, none spinning, available RAM 50632, slot 0
Software reset code 0x0012 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task Linu Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Aux1 errors 0,0,0
ADC conversions started 1063298, completed 1063298, timed out 0
Supply voltage: min 0.0, current 24.2, max 24.2, under voltage events: 1, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 14978, standstill, SG min/max 0/26, read errors 0, write errors 1, ifcnt 53, reads 41288, writes 23, timeouts 52, DMA errors 0, failedOp 0x71
Driver 1: position -1876, standstill, SG min/max 0/28, read errors 0, write errors 1, ifcnt 53, reads 41340, writes 23, timeouts 0, DMA errors 0
Driver 2: position 1034, standstill, SG min/max 0/30, read errors 0, write errors 1, ifcnt 52, reads 41286, writes 23, timeouts 54, DMA errors 0, failedOp 0x41
Driver 3: position 0, standstill, SG min/max 0/20, read errors 0, write errors 1, ifcnt 53, reads 41225, writes 23, timeouts 114, DMA errors 0, failedOp 0x6f
Driver 4: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 38, reads 41345, writes 18, timeouts 0, DMA errors 0
Driver 5: position 0, assumed not present
Driver 6: position 0, assumed not present
Date/time: 2021-03-27 14:33:58
Cache data hit count 3870301876
Slowest loop: 155.93ms; fastest: 0.08ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 0.0MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 93499ms, bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves 3625, completed moves 3625, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1, chamberHeaters = 2 -1
Heater 2 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 19160, send timeouts 19157, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 17 (min 17)
Last cancelled message type 4514 dest 127
=== SBC interface ===
State: 0, failed transfers: 0
Last transfer: 4ms ago
RX/TX seq numbers: 11810/11811
SPI underruns 0, overruns 0
Number of disconnects: 0, IAP RAM available 0x11458
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.2.2
Code buffer space: 4096
Configured SPI speed: 8000000 Hz
Full transfers per second: 36.36
Maximum length of RX/TX data transfers: 3576/1092
27/03/2021, 14:15:43	Error: G0/G1: insufficient axes homed
27/03/2021, 14:15:43	Cancelled printing file 0:/gcodes/tube_holder_0.12mm_PETG_ENDER3_4h12m.gcode, print time was 0h 16m
27/03/2021, 14:15:40	Warning: VIN under-voltage event (0.0V)
27/03/2021, 14:00:16	Height map loaded from file heightmap.csv
27/03/2021, 13:58:34	Warning: M307: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 603C
27/03/2021, 13:58:33	Connection established
27/03/2021, 13:55:41	Cancelled printing file 0:/gcodes/tube_holder_0.12mm_PETG_ENDER3_4h12m.gcode, print time was 0h 13m
27/03/2021, 13:44:13	Height map loaded from file heightmap.csv
27/03/2021, 13:39:00	Finished printing file 0:/gcodes/Stanley_Organiser_Box_Insert_v2_0.12mm_PLA_ENDER3_4h28m.gcode, print time was 4h 39m
27/03/2021, 12:30:23	Connection established
27/03/2021, 12:30:22	Connection interrupted, attempting to reconnect...
Message is too long
27/03/2021, 09:01:45	Height map loaded from file heightmap.csv
27/03/2021, 08:58:32	Warning: M307: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 603C
27/03/2021, 08:58:31	Connection established
27/03/2021, 08:58:27	Connection interrupted, attempting to reconnect...
DCS has been stopped
26/03/2021, 19:17:35	Connected to sapphirepro