4.3.2021, 13:30:36	M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.2.2 running on Duet 3 MB6HC v1.01 or later (standalone mode)
Board ID: 08DJM-956BA-NA3TJ-6J9DJ-3S86J-1T9AT
Used output buffers: 6 of 40 (25 max)
=== RTOS ===
Static ram: 149788
Dynamic ram: 93080 of which 76 recycled
Never used RAM 115888, free system stack 152 words
Tasks: NETWORK(ready,189) ETHERNET(blocked,110) HEAT(blocked,297) CanReceiv(blocked,927) CanSender(blocked,352) CanClock(blocked,352) TMC(blocked,19) MAIN(running,1119) IDLE(ready,19)
Owned mutexes:
=== Platform ===
Last reset 00:00:59 ago, cause: power up
Last software reset at 2021-03-04 13:27, reason: User, GCodes spinning, available RAM 115888, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Aux1 errors 0,0,0
MCU temperature: min 20.6, current 30.1, max 30.2
Supply voltage: min 24.4, current 24.5, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Driver 0: position 79717, standstill, reads 6872, writes 21 timeouts 0, SG min/max 0/661
Driver 1: position -84501, standstill, reads 6872, writes 21 timeouts 0, SG min/max 0/261
Driver 2: position 0, standstill, reads 6872, writes 21 timeouts 0, SG min/max 0/155
Driver 3: position 0, standstill, reads 6872, writes 21 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 6873, writes 21 timeouts 0, SG min/max 0/152
Driver 5: position 0, standstill, reads 6878, writes 16 timeouts 0, SG min/max 0/0
Date/time: 2021-03-04 13:30:36
Slowest loop: 4.09ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 2.4ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 19635ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 10, completed moves 10, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 6.87ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- Ethernet -
State: active
Error counts: 0 0 0 0 0
Socket states: 5 2 2 2 2 0 0 0
=== Filament sensors ===
Extruder 0 sensor: ok
=== CAN ===
Messages queued 239, send timeouts 533, received 0, lost 0, longest wait 0ms for reply type 0, free buffers 48