8/8/2020, 5:54:52 PM: G28: Height map loaded from file heightmap.csv
8/8/2020, 5:54:58 PM: G1 X0 Y0
8/8/2020, 5:55:11 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.2-beta running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956L2-G43S8-6J9DG-3S46Q-KV2GD
Used output buffers: 1 of 40 (10 max)
=== RTOS ===
Static ram: 155140
Dynamic ram: 171368 of which 56 recycled
Exception stack ram used: 520
Never used ram: 66132
Tasks: NETWORK(ready,1984) HEAT(blocked,1204) CanReceiv(suspended,3824) CanSender(suspended,1432) CanClock(blocked,1436) TMC(blocked,208) MAIN(running,4952) IDLE(ready,76)
Owned mutexes:
=== Platform ===
Last reset 00:01:00 ago, cause: software
Last software reset at 2020-08-08 22:54, reason: User, spinning module LinuxInterface, available RAM 66060 bytes (slot 0)
Software reset code 0x0010 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 36.9, current 38.0, max 38.1
Supply voltage: min 23.8, current 23.9, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Driver 0: position 0,  standstill, reads 33850, writes 11 timeouts 0, SG min/max 0/0
Driver 1: position 0,  standstill, reads 33847, writes 14 timeouts 0, SG min/max 0/0
Driver 2: position 828,  standstill, reads 33845, writes 17 timeouts 0, SG min/max 0/237
Driver 3: position 0,  standstill, reads 33851, writes 11 timeouts 0, SG min/max 0/0
Driver 4: position 0,  standstill, reads 33846, writes 17 timeouts 0, SG min/max 0/222
Driver 5: position 0,  standstill, reads 33846, writes 17 timeouts 0, SG min/max 0/205
Date/time: 2020-08-08 22:55:15
Slowest loop: 4.22ms; fastest: 0.14ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 374, MaxWait: 21392ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 19, completed moves: 19, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
DDA motion commanded -63194, 0
=== Heat ===
Bed heaters = 1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USBchan is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 1.02ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 0 of 8
- Ethernet -
State: disabled
Error counts: 0 0 0 0 0
Socket states: 0 0 0 0 0 0 0 0
=== CAN ===
Messages sent 233, send timeouts 0, longest wait 1ms for type 6018, free CAN buffers 49
Motion commanded 1000, -62194
=== SBC interface ===
State: 0, failed transfers: 0
Last transfer: 17ms ago
RX/TX seq numbers: 1729/1731
SPI underruns 0, overruns 0
Number of disconnects: 0
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.1.1
Code buffer space: 4096
Configured SPI speed: 8000000 Hz
Full transfers per second: 32.03
8/8/2020, 5:55:47 PM: M122 B40: Diagnostics for board 40:
Board EXP1XD firmware 3.1.0+ (2020-08-08b1)
Never used RAM 2.7Kb, max stack 360b
HEAT 1412 CanAsync 1448 CanRecv 1424 MAIN 2368 AIN 1012
Last reset 00:02:54 ago, cause: software
Driver 0: position 1000
Moves scheduled 11, completed 11, in progress 0, hiccups 0
No step interrupt scheduled
VIN: 24.2V
MCU temperature: min 24.3C, current 25.1C, max 25.3C
Ticks since heat task active 156, ADC conversions started 87325, completed 87324, timed out 0
Last sensors broadcast 00000000 found 0 159 ticks ago
Free CAN buffers: 36, messages lost 0, duplicates 0, motion 1000, oos 0
NVM user row b1d088a9 fffff8bb a 0
TSENS 0009cd GAIN 01493e OFFS 002874 CAL 1f28
8/8/2020, 5:55:56 PM: M122 B41: Diagnostics for board 41:
Board EXP1XD firmware 3.1.0+ (2020-08-08b1)
Never used RAM 2.7Kb, max stack 368b
HEAT 1412 CanAsync 1448 CanRecv 1424 MAIN 2368 AIN 1012
Last reset 00:02:53 ago, cause: software
Driver 0: position -123388
Moves scheduled 16, completed 16, in progress 0, hiccups 0
No step interrupt scheduled
VIN: 24.4V
MCU temperature: min 25.7C, current 26.7C, max 26.8C
Ticks since heat task active 106, ADC conversions started 86925, completed 86925, timed out 0
Last sensors broadcast 00000000 found 0 109 ticks ago
Free CAN buffers: 36, messages lost 0, duplicates 0, motion -123388, oos 0
NVM user row b1d088a9 fffff8bb a 0
TSENS 000a74 GAIN 0155f1 OFFS 00280f CAL 1f2c
8/8/2020, 5:57:43 PM: Upload of 3DBenchy (1).gcode successful after 0s
8/8/2020, 6:00:49 PM: M32 "0:/gcodes/3DBenchy (1).gcode": File 0:/gcodes/3DBenchy (1).gcode selected for printing
8/8/2020, 6:02:01 PM: M25: Printing paused at X69.7 Y37.8 Z0.4
8/8/2020, 6:02:07 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.2-beta running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956L2-G43S8-6J9DG-3S46Q-KV2GD
Used output buffers: 1 of 40 (14 max)
=== RTOS ===
Static ram: 155140
Dynamic ram: 171368 of which 56 recycled
Exception stack ram used: 520
Never used ram: 66132
Tasks: NETWORK(ready,1984) HEAT(blocked,1188) CanReceiv(suspended,3824) CanSender(suspended,1420) CanClock(blocked,1428) TMC(blocked,72) MAIN(running,4496) IDLE(ready,76)
Owned mutexes:
=== Platform ===
Last reset 00:07:56 ago, cause: software
Last software reset at 2020-08-08 22:54, reason: User, spinning module LinuxInterface, available RAM 66060 bytes (slot 0)
Software reset code 0x0010 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 37.9, current 41.8, max 41.9
Supply voltage: min 23.7, current 23.8, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Driver 0: position 5000,  standstill, reads 17086, writes 0 timeouts 0, SG min/max not available
Driver 1: position 0,  standstill, reads 17083, writes 3 timeouts 0, SG min/max 0/566
Driver 2: position 2241,  standstill, reads 17082, writes 4 timeouts 0, SG min/max 0/854
Driver 3: position 0,  standstill, reads 17086, writes 0 timeouts 0, SG min/max not available
Driver 4: position 0,  standstill, reads 17082, writes 4 timeouts 0, SG min/max 0/925
Driver 5: position 0,  standstill, reads 17082, writes 4 timeouts 0, SG min/max 0/687
Date/time: 2020-08-08 23:02:11
Slowest loop: 12.77ms; fastest: 0.21ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 349, MaxWait: 351107ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 3535, completed moves: 3535, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
DDA motion commanded -58194, 0
=== Heat ===
Bed heaters = 1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.4
Heater 1 is on, I-accum = 0.3
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is idle in state(s) 0
USBchan is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.67ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 0 of 8
- Ethernet -
State: disabled
Error counts: 0 0 0 0 0
Socket states: 0 0 0 0 0 0 0 0
=== CAN ===
Messages sent 8663, send timeouts 0, longest wait 4ms for type 6024, free CAN buffers 49
Motion commanded 1000, -57194
=== SBC interface ===
State: 0, failed transfers: 0
Last transfer: 16ms ago
RX/TX seq numbers: 15268/15270
SPI underruns 0, overruns 0
Number of disconnects: 0
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.1.1
Code buffer space: 4096
Configured SPI speed: 8000000 Hz
Full transfers per second: 32.53
File /opt/dsf/sd/gcodes/3DBenchy (1).gcode is selected, paused
8/8/2020, 6:02:33 PM: G1 X0 Y0
8/8/2020, 6:02:40 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.2-beta running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956L2-G43S8-6J9DG-3S46Q-KV2GD
Used output buffers: 1 of 40 (14 max)
=== RTOS ===
Static ram: 155140
Dynamic ram: 171368 of which 56 recycled
Exception stack ram used: 520
Never used ram: 66132
Tasks: NETWORK(ready,1984) HEAT(blocked,1188) CanReceiv(suspended,3824) CanSender(suspended,1420) CanClock(blocked,1428) TMC(blocked,72) MAIN(running,4496) IDLE(ready,76)
Owned mutexes:
=== Platform ===
Last reset 00:08:28 ago, cause: software
Last software reset at 2020-08-08 22:54, reason: User, spinning module LinuxInterface, available RAM 66060 bytes (slot 0)
Software reset code 0x0010 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 41.7, current 42.0, max 42.1
Supply voltage: min 23.7, current 23.7, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Driver 0: position 0,  standstill, reads 28008, writes 0 timeouts 0, SG min/max not available
Driver 1: position 0,  standstill, reads 28008, writes 0 timeouts 0, SG min/max not available
Driver 2: position 2241,  standstill, reads 28008, writes 0 timeouts 0, SG min/max not available
Driver 3: position 0,  standstill, reads 28008, writes 0 timeouts 0, SG min/max not available
Driver 4: position 0,  standstill, reads 28008, writes 0 timeouts 0, SG min/max not available
Driver 5: position 0,  standstill, reads 28008, writes 0 timeouts 0, SG min/max not available
Date/time: 2020-08-08 23:02:44
Slowest loop: 3.95ms; fastest: 0.22ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 3537, completed moves: 3537, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
DDA motion commanded -63194, 0
=== Heat ===
Bed heaters = 1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.4
Heater 1 is on, I-accum = 0.2
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is idle in state(s) 0
USBchan is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.47ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 0 of 8
- Ethernet -
State: disabled
Error counts: 0 0 0 0 0
Socket states: 0 0 0 0 0 0 0 0
=== CAN ===
Messages sent 134, send timeouts 0, longest wait 0ms for type 0, free CAN buffers 49
Motion commanded 1000, -62194
=== SBC interface ===
State: 0, failed transfers: 0
Last transfer: 20ms ago
RX/TX seq numbers: 16282/16284
SPI underruns 0, overruns 0
Number of disconnects: 0
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.1.1
Code buffer space: 4096
Configured SPI speed: 8000000 Hz
Full transfers per second: 31.37
File /opt/dsf/sd/gcodes/3DBenchy (1).gcode is selected, paused
8/8/2020, 6:02:50 PM: M122 B40: Diagnostics for board 40:
Board EXP1XD firmware 3.1.0+ (2020-08-08b1)
Never used RAM 2.7Kb, max stack 368b
HEAT 1412 CanAsync 1448 CanRecv 1424 MAIN 2368 AIN 1012
Last reset 00:09:57 ago, cause: software
Driver 0: position 1000
Moves scheduled 3365, completed 3365, in progress 0, hiccups 0
No step interrupt scheduled
VIN: 24.2V
MCU temperature: min 24.3C, current 25.1C, max 25.3C
Ticks since heat task active 104, ADC conversions started 298549, completed 298549, timed out 0
Last sensors broadcast 00000000 found 0 107 ticks ago
Free CAN buffers: 36, messages lost 0, duplicates 0, motion 1000, oos 0
NVM user row b1d088a9 fffff8bb a 0
TSENS 0009cd GAIN 01493e OFFS 002874 CAL 1f28
8/8/2020, 6:02:54 PM: M122 B41: Diagnostics for board 41:
Board EXP1XD firmware 3.1.0+ (2020-08-08b1)
Never used RAM 2.7Kb, max stack 368b
HEAT 1412 CanAsync 1448 CanRecv 1424 MAIN 2368 AIN 1012
Last reset 00:09:52 ago, cause: software
Driver 0: position -123388
Moves scheduled 3457, completed 3457, in progress 0, hiccups 0
No step interrupt scheduled
VIN: 24.4V
MCU temperature: min 25.7C, current 27.7C, max 27.7C
Ticks since heat task active 110, ADC conversions started 296052, completed 296052, timed out 0
Last sensors broadcast 00000000 found 0 114 ticks ago
Free CAN buffers: 36, messages lost 0, duplicates 0, motion -123388, oos 0
NVM user row b1d088a9 fffff8bb a 0
TSENS 000ad0 GAIN 0155f1 OFFS 00280f CAL 1f2c
8/8/2020, 6:03:05 PM: M24: Printing resumed
8/8/2020, 6:06:33 PM: M25: Printing paused at X56.9 Y25.0 Z2.6
8/8/2020, 6:06:38 PM: G1 X0 Y0
8/8/2020, 6:06:45 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.2-beta running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956L2-G43S8-6J9DG-3S46Q-KV2GD
Used output buffers: 1 of 40 (14 max)
=== RTOS ===
Static ram: 155140
Dynamic ram: 171368 of which 56 recycled
Exception stack ram used: 520
Never used ram: 66132
Tasks: NETWORK(ready,1984) HEAT(blocked,1188) CanReceiv(suspended,3824) CanSender(suspended,1420) CanClock(blocked,1428) TMC(blocked,72) MAIN(running,4496) IDLE(ready,76)
Owned mutexes:
=== Platform ===
Last reset 00:12:34 ago, cause: software
Last software reset at 2020-08-08 22:54, reason: User, spinning module LinuxInterface, available RAM 66060 bytes (slot 0)
Software reset code 0x0010 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 42.0, current 43.5, max 43.7
Supply voltage: min 23.7, current 23.8, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.2, max 12.2, under voltage events: 0
Driver 0: position 0,  standstill, reads 14566, writes 0 timeouts 0, SG min/max not available
Driver 1: position 0,  standstill, reads 14566, writes 0 timeouts 0, SG min/max 0/1023
Driver 2: position 3152,  standstill, reads 14566, writes 0 timeouts 0, SG min/max 0/1023
Driver 3: position 0,  standstill, reads 14567, writes 0 timeouts 0, SG min/max not available
Driver 4: position 0,  standstill, reads 14566, writes 0 timeouts 0, SG min/max 0/1023
Driver 5: position 0,  standstill, reads 14566, writes 0 timeouts 0, SG min/max 0/793
Date/time: 2020-08-08 23:06:49
Slowest loop: 12.68ms; fastest: 0.22ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 357, MaxWait: 125ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 8097, completed moves: 8097, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
DDA motion commanded -63194, 0
=== Heat ===
Bed heaters = 1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.3
Heater 1 is on, I-accum = 0.1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is idle in state(s) 0
USBchan is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.67ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 0 of 8
- Ethernet -
State: disabled
Error counts: 0 0 0 0 0
Socket states: 0 0 0 0 0 0 0 0
=== CAN ===
Messages sent 9923, send timeouts 0, longest wait 3ms for type 6024, free CAN buffers 49
Motion commanded 1000, -62194
=== SBC interface ===
State: 0, failed transfers: 0
Last transfer: 17ms ago
RX/TX seq numbers: 24211/24213
SPI underruns 0, overruns 0
Number of disconnects: 0
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.1.1
Code buffer space: 4096
Configured SPI speed: 8000000 Hz
Full transfers per second: 32.33
File /opt/dsf/sd/gcodes/3DBenchy (1).gcode is selected, paused
8/8/2020, 6:06:49 PM: M122 B40: Diagnostics for board 40:
Board EXP1XD firmware 3.1.0+ (2020-08-08b1)
Never used RAM 2.6Kb, max stack 424b
HEAT 1412 CanAsync 1448 CanRecv 1424 MAIN 2368 AIN 1012
Last reset 00:13:56 ago, cause: software
Driver 0: position 1000
Moves scheduled 7505, completed 7505, in progress 0, hiccups 0
No step interrupt scheduled
VIN: 24.2V
MCU temperature: min 24.3C, current 25.1C, max 25.3C
Ticks since heat task active 186, ADC conversions started 418465, completed 418465, timed out 0
Last sensors broadcast 00000000 found 0 189 ticks ago
Free CAN buffers: 36, messages lost 0, duplicates 0, motion 1000, oos 0
NVM user row b1d088a9 fffff8bb a 0
TSENS 0009cd GAIN 01493e OFFS 002874 CAL 1f28
8/8/2020, 6:06:57 PM: M122 B41: Diagnostics for board 41:
Board EXP1XD firmware 3.1.0+ (2020-08-08b1)
Never used RAM 2.7Kb, max stack 368b
HEAT 1412 CanAsync 1448 CanRecv 1424 MAIN 2368 AIN 1012
Last reset 00:13:55 ago, cause: software
Driver 0: position -123388
Moves scheduled 7552, completed 7552, in progress 0, hiccups 0
No step interrupt scheduled
VIN: 24.4V
MCU temperature: min 25.7C, current 28.1C, max 28.2C
Ticks since heat task active 212, ADC conversions started 417603, completed 417603, timed out 0
Last sensors broadcast 00000000 found 0 215 ticks ago
Free CAN buffers: 36, messages lost 0, duplicates 0, motion -123388, oos 0
NVM user row b1d088a9 fffff8bb a 0
TSENS 000aed GAIN 0155f1 OFFS 00280f CAL 1f2c
8/8/2020, 6:07:08 PM: M24: Printing resumed
8/8/2020, 6:13:11 PM: M25: Printing paused at X50.9 Y33.4 Z6.6
8/8/2020, 6:13:17 PM: G1 X0 Y0
8/8/2020, 6:13:25 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.2-beta running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956L2-G43S8-6J9DG-3S46Q-KV2GD
Used output buffers: 1 of 40 (14 max)
=== RTOS ===
Static ram: 155140
Dynamic ram: 171368 of which 56 recycled
Exception stack ram used: 520
Never used ram: 66132
Tasks: NETWORK(ready,1984) HEAT(blocked,1188) CanReceiv(suspended,3824) CanSender(suspended,1420) CanClock(blocked,1428) TMC(blocked,72) MAIN(running,4496) IDLE(ready,76)
Owned mutexes:
=== Platform ===
Last reset 00:19:13 ago, cause: software
Last software reset at 2020-08-08 22:54, reason: User, spinning module LinuxInterface, available RAM 66060 bytes (slot 0)
Software reset code 0x0010 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 43.4, current 44.5, max 44.6
Supply voltage: min 23.7, current 23.9, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Driver 0: position 0,  standstill, reads 44563, writes 0 timeouts 0, SG min/max not available
Driver 1: position 0,  standstill, reads 44562, writes 0 timeouts 0, SG min/max 0/961
Driver 2: position 4809,  standstill, reads 44563, writes 0 timeouts 0, SG min/max 0/1023
Driver 3: position 0,  standstill, reads 44562, writes 0 timeouts 0, SG min/max not available
Driver 4: position 0,  standstill, reads 44563, writes 0 timeouts 0, SG min/max 0/1023
Driver 5: position 0,  standstill, reads 44562, writes 0 timeouts 0, SG min/max 0/1023
Date/time: 2020-08-08 23:13:29
Slowest loop: 12.76ms; fastest: 0.22ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 356, MaxWait: 107ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 17700, completed moves: 17700, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
DDA motion commanded -63194, 0
=== Heat ===
Bed heaters = 1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.3
Heater 1 is on, I-accum = 0.1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is idle in state(s) 0
USBchan is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.68ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 0 of 8
- Ethernet -
State: disabled
Error counts: 0 0 0 0 0
Socket states: 0 0 0 0 0 0 0 0
=== CAN ===
Messages sent 20467, send timeouts 0, longest wait 3ms for type 6024, free CAN buffers 49
Motion commanded 1000, -62194
=== SBC interface ===
State: 0, failed transfers: 0
Last transfer: 17ms ago
RX/TX seq numbers: 36833/36835
SPI underruns 0, overruns 0
Number of disconnects: 0
Buffer RX/TX: 0/360-0
=== Duet Control Server ===
Duet Control Server v3.1.1
File:
Buffered code: G1 X98.315 Y31.496 E0.7595
==> 48 bytes
Code buffer space: 3736
Configured SPI speed: 8000000 Hz
Full transfers per second: 31.57
File /opt/dsf/sd/gcodes/3DBenchy (1).gcode is selected, processing, paused
8/8/2020, 6:13:30 PM: M122 B40: Diagnostics for board 40:
Board EXP1XD firmware 3.1.0+ (2020-08-08b1)
Never used RAM 2.6Kb, max stack 424b
HEAT 1404 CanAsync 1448 CanRecv 1424 MAIN 2368 AIN 1012
Last reset 00:20:37 ago, cause: software
Driver 0: position 1000
Moves scheduled 16312, completed 16312, in progress 0, hiccups 0
No step interrupt scheduled
VIN: 24.2V
MCU temperature: min 24.3C, current 25.1C, max 25.3C
Ticks since heat task active 50, ADC conversions started 618772, completed 618772, timed out 0
Last sensors broadcast 00000000 found 0 54 ticks ago
Free CAN buffers: 36, messages lost 0, duplicates 0, motion 1000, oos 0
NVM user row b1d088a9 fffff8bb a 0
TSENS 0009cd GAIN 01493e OFFS 002874 CAL 1f28
8/8/2020, 6:13:37 PM: M122 B41: Diagnostics for board 41:
Board EXP1XD firmware 3.1.0+ (2020-08-08b1)
Never used RAM 2.7Kb, max stack 368b
HEAT 1404 CanAsync 1448 CanRecv 1424 MAIN 2368 AIN 1012
Last reset 00:20:35 ago, cause: software
Driver 0: position -123388
Moves scheduled 16333, completed 16333, in progress 0, hiccups 0
No step interrupt scheduled
VIN: 24.4V
MCU temperature: min 25.7C, current 27.9C, max 28.3C
Ticks since heat task active 178, ADC conversions started 617586, completed 617585, timed out 0
Last sensors broadcast 00000000 found 0 181 ticks ago
Free CAN buffers: 36, messages lost 0, duplicates 0, motion -123388, oos 0
NVM user row b1d088a9 fffff8bb a 0
TSENS 000af4 GAIN 0155f1 OFFS 00280f CAL 1f2c