5/25/2020, 1:12:29 PM: : Finished printing file 0:/gcodes/CuttingBoardHangerBase.gcode, print time was 0h 33m
5/25/2020, 1:39:29 PM: Successfully deleted CuttingBoardHangerHalves.gcode
5/25/2020, 1:39:35 PM: Upload of CuttingBoardHangerHalves.gcode successful after 2s
5/25/2020, 1:39:39 PM: M32 "0:/gcodes/CuttingBoardHangerHalves.gcode": File 0:/gcodes/CuttingBoardHangerHalves.gcode selected for printing
5/25/2020, 1:39:42 PM: : Warning: Lost connection to Duet (Timeout while waiting for transfer ready pin)
5/25/2020, 1:39:59 PM: : Connection to Duet established
5/25/2020, 1:39:59 PM: : Warning: Controller has been reset

5/25/2020, 1:40:38 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.1.1 running on Duet 3 MB6HC v0.6 or 1.0 (SBC mode)
Board ID: 08DJM-956L2-G43S8-6J1FA-3SS6K-1B1QH
Used output buffers: 1 of 40 (16 max)
=== RTOS ===
Static ram: 154604
Dynamic ram: 165376 of which 44 recycled
Exception stack ram used: 224
Never used ram: 72968
Tasks: NETWORK(ready,1980) HEAT(blocked,1124) CanReceiv(suspended,3512) CanSender(suspended,1488) CanClock(blocked,1452) TMC(blocked,204) MAIN(running,4992) IDLE(ready,76)
Owned mutexes:
=== Platform ===
Last reset 00:00:38 ago, cause: software
Last software reset at 2020-05-25 18:39, reason: Assertion failed, spinning module GCodes, available RAM 71820 bytes (slot 0)
Software reset code 0x4123 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a80f BFAR 0x00000000 SP 0x2045fe9c Task MAIN
Stack: 00000194 00484cd0 00463dbf 00000001 0045831f 20428990 2044cd58 2044cc08 2043f1a8 00000001 2043f120 
Error status: 0
MCU temperature: min 34.1, current 34.6, max 34.9
Supply voltage: min 24.1, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.2, max 12.2, under voltage events: 0
Driver 0: standstill, reads 59192, writes 14 timeouts 0, SG min/max 0/0
Driver 1: standstill, reads 59193, writes 14 timeouts 0, SG min/max 0/0
Driver 2: standstill, reads 59193, writes 14 timeouts 0, SG min/max 0/0
Driver 3: standstill, reads 59194, writes 14 timeouts 0, SG min/max 0/0
Driver 4: standstill, reads 59194, writes 14 timeouts 0, SG min/max 0/0
Driver 5: standstill, reads 59193, writes 15 timeouts 0, SG min/max 0/0
Date/time: 2020-05-25 18:40:38
Slowest loop: 7.07ms; fastest: 0.14ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 6 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = 7 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.82ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 0 of 8
- Ethernet -
State: disabled
Error counts: 0 0 0 0 0
Socket states: 0 0 0 0 0 0 0 0
=== CAN ===
Messages sent 206, longest wait 2ms for type 6012
=== Linux interface ===
State: 0, failed transfers: 0
Last transfer: 19ms ago
RX/TX seq numbers: 59289/1236
SPI underruns 0, overruns 0
Number of disconnects: 0
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.1.1
Code buffer space: 4096
Configured SPI speed: 8000000 Hz
Full transfers per second: 21.89