; Configuration file for Duet Wifi

; generated by Ingenieurbüro Christian Reil 

; General preferences
G90                                      ; Send absolute coordinates...
M82                                      ; and absoulute extruder  moves

M667 S1                                  ; Select CoreXY mode

; Network
M550 P"C1-C00017"                        ; Set machine name
M552 P192.168.188.100 S1                 ; Enable network and acquire dynamic address via DHCP
M586 P0 S1                               ; Enable HTTP
M586 P1 S0                               ; Disable FTP
M586 P2 S0                               ; Disable Telnet

; Drives
M569 P0 S0  D2                             ; Drive 0 goes backwards
M569 P1 S0  D2                            ; Drive 1 goes backwards
M569 P2 S0  D2                             ; Drive 2 goes backwards
M569 P3 S0  D2                            ; Drive 3 goes backwards
M569 P4 S0  D2                             ; Drive 4 goes backwards
M584 X0 Y1 Z2 E3
M350 X64 Y64 Z16 E16 I1                  ; Configure microstepping with interpolation
M92 X320 Y320 Z1600.00 E414.00          ; Set steps per mm

M566 X500.00 Y500.00 Z12.00 E500.00      ; vorher 400 Set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z1000.00 E9000.00  ; Set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1500.00 E900.00      ; Set accelerations (mm/s^2)

M906 X1000.00 Y1000.00 Z1400.00 E1000.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                  ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                         ; Set axis minima
M208 X300 Y220 Z250 S0                   ; Set axis maxima

; Endstops
M574 X2 Y2 S1                         ; Set active high endstops

;Filament Sensor
;M581 T2 E0 S1 C0		      ; additional trigger #3 (calls trigger3.g), connected on Extruder Endstops, trigger on  rising edge, only trigger while printing
;M582 T2

; Z-Probe
M574 Z1 S2                               ; Set endstops controlled by probe
M558 P1 H7 F150 T6000                   ; Set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y35 Z4.00          ; Set Z probe trigger value, offset and trigger height
M557 X20:280 Y35:180 P08:08                 

; Open Door Switch
;M581 T3 Z S1 C0			    ; additional trigger #2 (calls trigger2.g), connected on z-endstop, trigger on  rising edge, only trigger while printing
;M582 T3

; LED
M106 P2 S150		     ; signal line for LED at fan1


; Heaters
M305 P0 T100000 B4725 C7.060000e-8 	 ; Set thermistor + ADC parameters for heater 0
M143 H0 S70                             ; Set temperature limit for heater 0 to 70C
M305 P1 T100000 B4725 C7.060000e-8       ; Set thermistor + ADC parameters for heater 1
M143 H1 S250  		                 ; Set temperature limit for heater 1 to 250C

; Fans
M106 P1 S0 I0 F500 H1 T45                ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P0 S0 I0 F500 H-1                   ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off

; Tools
M563 P0 D0 H1                            ; Define tool 0
G10 P0 X0 Y0 Z0                          ; Set tool 0 axis offsets
G10 P0 R190 S0                        ; Set initial tool 0 active and standby temperatures to 0C


; Custom settings are not configured
T0 P0;
M400;

M572 D0 S0.05;

M501;