6:07:08 PM
Error: M141: No chamber heater has been configured for slot 0
6:06:58 PM
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02(RTOS) running on Duet WiFi 1.02 or later
Board ID: 08DGM-917DA-G4MS8-6JKDA-3S06M-T8T7B
Used output buffers: 1 of 20 (13 max)
=== RTOS ===
Static ram: 25524
Dynamic ram: 98676 of which 12 recycled
Exception stack ram used: 592
Never used ram: 6268
Tasks: NETWORK(ready,676) HEAT(blocked,1232) MAIN(running,3788) IDLE(ready,200)
Owned mutexes:
=== Platform ===
Last reset 00:02:09 ago, cause: software
Last software reset at 2019-08-07 18:04, reason: User, spinning module GCodes, available RAM 6584 bytes (slot 2)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 2.9ms, max retries 0
MCU temperature: min 36.1, current 37.3, max 37.5
Supply voltage: min 23.3, current 24.1, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/249
Driver 1: ok, SG min/max 0/268
Driver 2: ok, SG min/max 0/243
Driver 3: ok, SG min/max 0/218
Driver 4: standstill, SG min/max not available
Date/time: 2019-08-07 18:06:57
Cache data hit count 449599003
Slowest loop: 45.16ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0
=== Move ===
Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 230, MinFreeDm: 223, MaxWait: 28003ms, Underruns: 0, 0
Scheduled moves: 68, completed moves: 65
Bed compensation in use: mesh
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.1
Heater 1 is on, I-accum = 0.3
=== GCodes ===
Segments left: 1
Stack records: 2 allocated, 1 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 2 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 22.82ms; fastest: 0.00ms
Responder states: HTTP(4) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
- WiFi -
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.22
WiFi MAC address ec:fa:bc:2d:d9:71
WiFi Vcc 3.42, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 29320
WiFi IP address 10.10.10.32
WiFi signal strength -60dBm, reconnections 0, sleep mode modem
Socket states: 0 2 0 0 0 0 0 0
=== Filament sensors ===
Extruder 0 sensor: ok
6:06:50 PM
16 points probed, mean error -0.299, deviation 0.435
Height map saved to file heightmap.csv
6:05:17 PM
Error: Pop(): stack underflow!
6:05:05 PM
M32 "Front_Panel_-_Center_plate.gcode"
File Front_Panel_-_Center_plate.gcode selected for printing
6:04:57 PM
Connection established!
6:04:47 PM
M112
M999
Cancelled printing file Front_Panel_-_Center_plate.gcode, print time was 0h 0m
6:03:41 PM
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02(RTOS) running on Duet WiFi 1.02 or later
Board ID: 08DGM-917DA-G4MS8-6JKDA-3S06M-T8T7B
Used output buffers: 3 of 20 (9 max)
=== RTOS ===
Static ram: 25524
Dynamic ram: 98640 of which 12 recycled
Exception stack ram used: 312
Never used ram: 6584
Tasks: NETWORK(ready,544) HEAT(blocked,1232) MAIN(running,3844) IDLE(ready,200)
Owned mutexes:
=== Platform ===
Last reset 00:03:08 ago, cause: software
Last software reset at 2019-08-07 18:00, reason: User, spinning module GCodes, available RAM 6584 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 3.1ms, max retries 0
MCU temperature: min 36.5, current 36.6, max 37.4
Supply voltage: min 20.7, current 23.9, max 24.8, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max 38/250
Driver 3: standstill, SG min/max 0/166
Driver 4: standstill, SG min/max not available
Date/time: 2019-08-07 18:03:41
Cache data hit count 670102658
Slowest loop: 42.65ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0
=== Move ===
Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm: 238, MaxWait: 176121ms, Underruns: 0, 0
Scheduled moves: 1, completed moves: 1
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.2
Heater 1 is on, I-accum = 0.3
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "M190 S60 " in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 22.97ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
- WiFi -
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.22
WiFi MAC address ec:fa:bc:2d:d9:71
WiFi Vcc 3.42, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 29128
WiFi IP address 10.10.10.32
WiFi signal strength -58dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
=== Filament sensors ===
Extruder 0 sensor: ok
6:03:30 PM
Resume state saved
Print auto-paused due to low voltage
6:03:30 PM
M32 "Front_Panel_-_Center_plate.gcode"
File Front_Panel_-_Center_plate.gcode selected for printing
6:00:42 PM
Connection established!