; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Tue May 21 2019 23:59:03 GMT+0100 (GMT+01:00)

; General preferences
G90                                                                        ; Send absolute coordinates...
M83                                                                        ; ...but relative extruder moves

; Network
M550 P"Ender3"                                                             ; Set machine name
M552 S1                                                                    ; Enable network
M587 S”my wifie“ P”password” I192.168.1.111 J192.168.1.1 K255.255.255.0    ; Configure access point and IP addresses. You can delete this line once connected
M586 P0 S1                                                                 ; Enable HTTP
M586 P1 S1                                                                 ; Enable FTP
M586 P2 S1                                                                 ; Enable Telnet

; Drives
M569 P0 S0                                                                 ; Physical drive 0 goes backwards
M569 P1 S0                                                                 ; Physical drive 1 goes backwards
M569 P2 S1                                                                 ; Physical drive 2 goes forwards
M569 P3 S0                                                                 ; Physical drive 3 goes backwards
M350 X16 Y16 Z16 E16 I1                                                    ; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E837.00                                          ; Set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00                                        ; Set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00                                    ; Set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00                                        ; Set accelerations (mm/s^2)
M906 X800.00 Y800.00 Z800.00 E925.00 I20                                   ; Set motor currents (mA) and motor idle factor in per cent
M84 S300                                                                   ; Set idle timeout

; Axis Limits
M208 X-5.5 Y-10 Z0 S1                                                      ; Set axis minima
M208 X250 Y246 Z260 S0                                                     ; Set axis maxima

; Endstops
M574 X1 Y1 S1                                                              ; Set active high endstops

; Z-Probe
M574 Z1 S2                                                                 ; Set endstops controlled by probe
M307 H3 A-1 C-1 D-1                                                        ; Disable heater on PWM channel for BLTouch
M558 P9 H2.5 F60 T6000                                                     ; Set Z probe type to bltouch and the dive height + speeds
G31 P25 X42 Y-4 Z1.395                                                     ; Set Z probe trigger value, offset and trigger height
M557 X-5.5:200 Y10:215 S20                                                 ; Define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700                                                ; Set thermistor + ADC parameters for heater 0
M143 H0 S120                                                               ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700                                                ; Set thermistor + ADC parameters for heater 1
M143 H1 S285                                                               ; Set temperature limit for heater 1 to 285C

; Fans
M106 P0 S0.3 I0 F500 H1 T45                                                ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45                                                  ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45                                                  ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1                                                              ; Define tool 0
G10 P0 X0 Y0 Z0                                                            ; Set tool 0 axis offsets
G10 P0 R0 S0                                                               ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"                         ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured