17:44:57
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02RC1(RTOS) running on Duet WiFi 1.0 or 1.01
Board ID: 08DAM-999TL-MQ4SD-6J9FD-3SJ6J-K593W
Used output buffers: 8 of 20 (20 max)
=== RTOS ===
Static ram: 28460
Dynamic ram: 98412 of which 0 recycled
Exception stack ram used: 460
Never used ram: 3740
Tasks: NETWORK(ready,328) HEAT(blocked,1192) MAIN(running,3548)
Owned mutexes:
=== Platform ===
Last reset 07:09:03 ago, cause: power up
Last software reset at 2018-09-05 21:07, reason: User, spinning module GCodes, available RAM 3740 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 4
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 32.6, current 33.4, max 33.6
Supply voltage: min 11.9, current 12.2, max 12.4, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max 0/313
Driver 1: standstill, SG min/max 0/297
Driver 2: standstill, SG min/max 0/296
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2018-09-06 17:45:01
Slowest loop: 9.87ms; fastest: 0.08ms
=== Move ===
Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm: 234, MaxWait: 4884870ms, Underruns: 0, 0
Scheduled moves: 11, completed moves: 11
Bed compensation in use: mesh
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.2
Heater 1 is on, I-accum = 0.2
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 177.32ms; fastest: 0.08ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 2 of 8
- WiFi -
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.21
WiFi MAC address 5c:cf:7f:2c:24:6b
WiFi Vcc 3.37, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 13936
WiFi IP address 192.168.1.16
WiFi signal strength -50dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
=== Expansion ===
17:44:26
M20
"hiddenhinged_box pins only hk trans 0.92 faster 195 190.gcode","Universal_Phone_and_Tablet_Stand.gcode","clamp18 trans hk pla.gcode","Pulley_T-MXL-XL-HTD-GT2_N-tooth 16 tooth idler depth 00 trans pla.gcode","base1 ri pla white.gcode","hiddenhinged_box pins only ri pla blue 0.97.gcode","base2 ri pla white.gcode","base3 ri pla white.gcode","Fidget_Cubes 8mm 0.3 gap hk pla trans 0.92 5 1st layer 80 speed.gcode"
17:42:41
G10 P0 S165
17:42:18
G10
17:42:04
G10
17:40:28
G28
17:40:05
M98 P"0:/macros/Movement/1 Centre"
17:39:55
G28
17:38:30
M666
Endstop adjustments X-1.22 Y-0.04 Z1.26, tilt X0.21% Y0.80%
17:37:56
M665
Diagonal 360.250, delta radius 167.697, homed height 254.773, bed radius 120.0, X -0.100°, Y -0.529°, Z 0.000°
17:36:44
M122
16:18:29
Finished printing file base3 ri pla white.gcode, print time was 2h 20m